Brilix XHPFD 140 E - User Manual

Questions and Answers

C
Cynthia MoraAug 14, 2025
Why does my Brilix Heat Pump show a high pressure error?
- T
  Tammy CampbellAug 15, 2025
  A high pressure error in your Brilix Heat Pump can occur due to several reasons: * Too much refrigerant: In this case, drain the excess refrigerant. * High water or environment temperature: Clean the air heat exchanger. * Operating frequency too high: Check and reconnect the electrical cables from the high pressure switch and replace the high pressure switch. Additionally, ensure there are no gas leaks (contact a specialized company to add refrigerant if needed), clean the air heat exchanger, replace the filter, and check/reconnect the electrical cables from the low pressure switch, potentially replacing the low pressure switch.
J
james00Aug 17, 2025
What to do if my Brilix XHPFD 140 E Heat Pump has low pressure error?
- O
  oliviafernandezAug 18, 2025
  If your Brilix Heat Pump displays a low pressure error, it could be due to: 1. Not enough refrigerant: Check for gas leaks and have a specialized company add refrigerant. 2. Insufficient flow: Clean the air heat exchanger. 3. Dirty filter: Replace the filter. 4. EEV failure. 5. Fan motor fault. 6. Low pressure switch failure: Check and reconnect the electrical cables from the low pressure switch, and if necessary, replace the low pressure switch.
B
Bobby WilliamsAug 21, 2025
What to do if my Brilix Heat Pump has impaired water flow?
- N
  Noah MerrittAug 21, 2025
  If you are experiencing impaired water flow with your Brilix Heat Pump, it could be caused by: weak water flow, flow in the wrong direction, or flow switch failure. To resolve this: 1. Ensure the water flow is sufficient. 2. Make sure the water flow switch is connected correctly. 3. Check the wiring to the water flow switch. 4. Replace with a new water flow switch if necessary.
R
Richard JohnsonAug 25, 2025
How to fix sensor error inlet water temperature in Brilix Heat Pump?
- S
  shane40Aug 25, 2025
  If your Brilix Heat Pump displays a sensor error for the inlet water temperature, it indicates that the sensor is either open or short circuited. To resolve this, check or replace the sensor.
T
timothysavageAug 27, 2025
How to fix sensor error outlet water temperature in Brilix Heat Pump?
- N
  nichole01Aug 28, 2025
  If your Brilix Heat Pump displays a sensor error for the outlet water temperature, it means the sensor is either open or short circuited. You should check or replace the sensor.
D
Daniel JohnsonAug 31, 2025
How to fix sensor error heating condenser in Brilix XHPFD 140 E?
- H
  hmillerAug 31, 2025
  If your Brilix Heat Pump shows a sensor error for the heating condenser, the sensor is likely open or short circuited. The suggested solution is to check or replace the sensor.
J
James LindseySep 3, 2025
How to fix sensor error gas return in Brilix XHPFD 140 E Heat Pump?
- B
  bfranklinSep 3, 2025
  If your Brilix Heat Pump displays a sensor error related to gas return, it indicates that the sensor is either open or short-circuited. The solution is to check or replace the sensor.
A
amy27Sep 6, 2025
How to fix sensor error ambient temperature in Brilix XHPFD 140 E?
- P
  patrickcomptonSep 7, 2025
  If your Brilix Heat Pump is showing a sensor error for the ambient temperature, this indicates the sensor is open or short circuited. You should check or replace the sensor.
B
Brandon CoffeySep 10, 2025
How to fix sensor error gas at the condenser output in Brilix XHPFD 140 E?
- D
  David PetersonSep 12, 2025
  If your Brilix Heat Pump displays a sensor error for gas at the condenser output, it means the sensor is either open or short circuited. You should check or replace the sensor.