EasyManua.ls Logo

Brinsea ChickSafe Eco Door Opener User Manual

Brinsea ChickSafe Eco Door Opener
7 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
1
ChickSafe Eco Door Opener with Door: Installation and Operating Instructions
IMPORTANT INSTALLATION NOTES!
The door must be attached to the opener BEFORE installing the batteries. Do not fit the batteries until
the ChickSafe and door are fully installed.
The door must be lifted and held in the open position before attaching the cord. The ChickSafe is supplied
with the cord wound in ready to be attached to the open door. It will return to this position each time it
opens.
The door must stop against a solid surface at its closed position. The ChickSafe detects when the weight
of the door is no longer being supported on the cord and that lets the control know the door is closed.
The distance the door moves between its closed position and open position must be no greater than
400mm (15 inches). If the door moves down through a greater distance the cord will wind back in again
and the door will be open even when the ChickSafe shows it is closed (double flashes of the LED light).
Do not remove the knot in the cord that was tied there at the factory. This knot operates the sensing
device to stop the ChickSafe in the open position.
If using with an alternative door, ensure the maximum door weight of 4kg (8lbs) is not exceeded as this
will cause damage to the motor and invalidate the guaranty! Note that wooden doors are heavier when
wet.
Check the sliding door to make sure it runs smoothly and reliably both upwards and downwards. The
ChickSafe uses gravity alone to close the door.
To mount the ChickSafe further away from the door, an additional length of cord may be attached to the
end of the internal cord. Do not wind out any cord from inside the ChickSafe.
For helpful information see our ChickSafe ‘Frequently Asked Questions’ page and installation videos at
www.brinsea.co.uk
Please read these instructions carefully before setting up your ChickSafe Eco to achieve best results and keep these
instructions safe for future reference.
To register your new Brinsea product and qualify for your free 3 year guaranty please visit www.brinsea.co.uk
within 30 days of purchase and follow the link on the Brinsea home page. The serial number may be found on the
box and inside the battery compartment. Sign up for the Brinsea newsletter to receive the latest news and
information.
Warning - Risk of injury! Keep fingers clear of moving door and cord. Motor may start without warning.
This appliance can be used by children aged from 8 years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience and knowledge if they have been given supervision
or instruction concerning use of the appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children
without supervision.
CS015 GB Issue 03
Question and Answer IconNeed help?

Do you have a question about the Brinsea ChickSafe Eco Door Opener and is the answer not in the manual?

Brinsea ChickSafe Eco Door Opener Specifications

General IconGeneral
BrandBrinsea
ModelChickSafe Eco Door Opener
CategoryFarm Equipment
LanguageEnglish

Summary

Important Installation Notes

Pre-Installation Checks and Warnings

Crucial notes before attaching the door and installing batteries, including door movement limits.

Door Installation Guide

Door Panel Preparation and Assembly

Steps for preparing door panels, fitting grommets, screws, and nuts.

Channel Fitting and Door Movement Test

Securing channels to the hen house and testing door slide for smooth operation.

ChickSafe Unit Installation and Operation

Unit Mounting and Cord Attachment

Attaching the ChickSafe unit to the hen house and connecting the door cord.

Battery Installation and Initial Setup

Inserting batteries, fitting the cover, and preparing the device for operation.

Door Operation Testing

Verifying the door opens and closes correctly based on light conditions.

LED Indicator Status and Troubleshooting

Understanding LED signals for device status and identifying potential issues.

Adjustments and Maintenance

Closing Light Level Adjustment

Customizing the light level threshold for automatic door closure at dusk.

Cleaning Instructions

Guidelines for safely cleaning the ChickSafe Eco unit using a damp cloth.

System Reset Procedure

Steps to reset the device to factory default settings if issues arise.

Related product manuals