To Next PageTo Next PageWhy does my Broan Platinum or Deco-Touch Fan wall control screen alternate between normal display and E3?
If your Broan Platinum or Deco-Touch wall control screen alternates between the normal display and E3, the Platinum or Deco-Touch wall control may be defective and needs to be replaced.
What to do if Broan Fan defrost cycle does not work?
If the defrost cycle on your Broan Fan isn't working, it could be due to several reasons. Ice deposit may be hindering the damper operation, so remove the ice. The damper rod or the port damper itself may be broken, so inspect these parts and replace if necessary. The damper actuator may be defective: plug in the unit, select “MIN” or “MAX”, and press the door switch to see if the port damper opens. If it doesn’t, feed 120V directly to the damper actuator, and if it still doesn't open, replace it. The circuit board may be defective. Unplug the unit, unplug the defrost sensor wire, plug the unit back in, select “MIN”, and ensure the unit is adjusted for low-speed operation. If this doesn't happen, replace the circuit board. Finally, the thermistor may be defective. If the defrost mode works...
Why is no outside temperature displayed on the screen of my Broan HRV200H Platinum wall control?
If there is no outside temperature displayed on the screen of your Broan Fan Platinum wall control, set the wall control on MIN or MAX in VENT Mode. If the problem persists, contact your installer.
How to fix air that is too dry with my Broan HRV200H?
If the air is too dry when using your Broan Fan, temporarily use a humidifier.
What to do if error code E1 or E3 appears on the screen of my Broan HRV200H wall control?
If error code E1 or E3 appears on the screen of your Platinum or Deco-Touch Broan Fan wall control, contact your installer.
How to fix air that is too cold at the air supply grille of my Broan HRV200H Fan?
If the air is too cold at the air supply grille of your Broan Fan, operate the unit at low speed (MIN.) or temporarily switch to the intermittent mode.
What to do if all light indicators on the Broan HRV200H wall control are flashing?
If all the light indicators on your Broan Fan wall control are flashing, clean the fan assembly. If the problem persists after cleaning, contact your installer.
Why is there condensation on my windows with Broan HRV200H Fan?
If you're experiencing condensation on your windows, indicating the air is too humid, adjust the humidity control knob as per instructions. Operate the Broan Fan at maximum speed during activities that generate excess humidity, such as family gatherings or extensive cooking. Leave curtains half-open to allow air circulation. Store firewood in a closed room with a dehumidifier, a well-ventilated room, or outside. Keep the temperature in your house above 18°C (64°F), and do not adjust your Dehumidistat below -20°C (-4°F).
Why is there a difference between the temperature displayed and the real temperature on my Broan Platinum Fan wall control?
If there's a significant difference between the displayed and actual temperature on your Broan Platinum wall control, the unit thermistor may be defective, so replace it. Alternatively, the unit damper might be blocked or broken; check its operation and replace if necessary.
What to do if Broan HRV200H Fan unit does not work?
First, unplug the Broan Fan unit. Disconnect the main B control and the optional G control(s), if applicable. Jump the B and G terminals, then plug the unit back in. If the motor runs on high speed and the damper opens, the circuit board is likely not defective. Alternatively, the power cord fuse may be blown. To check, unplug the unit and unscrew the fuse holder. If the fuse strand is broken, replace the fuse according to the specifications on the unit power cord tag.
Highlights critical safety instructions, potential hazards, and operational precautions for user safety and equipment protection.
Emphasizes using genuine manufacturer parts and seeking professional service for optimal performance and safety.
Details the main components of the ventilation unit, including power cord, filters, core, tray, and blower assembly.
Explains the function of the ventilation system in providing fresh air and exhausting stale, humid air to maintain indoor air quality.
Describes how units with a polypropylene core recover heat from exhaust air to warm incoming fresh air without mixing.
Explains the function of an enthalpic core for reducing ventilation costs by transferring heat and humidity between air streams.
Details the unit's defrost cycle operation when outside temperatures drop below freezing to prevent frost buildup in the core.
Provides technical specifications for different ventilation unit models, including dimensions, weight, and power consumption.
Introduces various control devices for the ventilation unit and directs users to specific pages for operation instructions.
Instructions for operating the Platinum main control panel for ventilation and recirculation modes.
Guide to using the Deco-Touch main control for managing ventilation modes like OFF, RECIRC, MIN, and MAX.
Explains how to operate the VT1W main control for adjusting air supply and condensation settings.
Details the operation of the VT2W main control, including air supply and condensation adjustments.
Instructions for using the Dehumidistat control to manage indoor humidity levels during different seasons.
Information on operating the 3-position switch for adjusting air supply speed on specific HRV models.
Guide to using 20-min, 20/40/60-min push-button timers, and 60-minute crank timer for timed ventilation.
Explains the various indicators and symbols displayed on the Platinum control screen for ventilation status and settings.
Details the physical indicators (power, filter maintenance) and function keys (SMART, SET, arrows, MODE/PREF, Reset) on the Platinum control unit.
Guides users through setting preferences like current day, time, temperature units, and backlight options on the Platinum control.
Provides step-by-step instructions for navigating and selecting values for various settings on the Platinum control.
Explains how to customize the ventilation unit's operation by setting daily periods, starting hours, and ventilation speeds.
Describes how the backlight on the Deco-Touch control activates and deactivates upon button presses.
Details the different operating modes of the Deco-Touch control: OFF, RECIRC, 20 MIN/H, MIN, and MAX.
Guides users on setting desired indoor humidity levels and selecting standby modes (OFF or RECIRCULATION).
Explains how to use the dehumidistat override for high-speed exchange to manage indoor humidity, especially in non-heating seasons.
Describes the maintenance indicator on the control and how to reset it after performing maintenance.
Instructions on selecting air supply speeds (MIN, MAX) and turning the unit OFF using the VT1W control.
Guides on setting the condensation control for summer and winter/spring months to manage window condensation.
Details on adjusting air supply (MIN, MAX, INTERMITTENT) and turning off the unit using the VT2W control.
Explains how to adjust the condensation control on the VT2W for summer and winter/spring to manage humidity.
Explains the meaning of the light indicators on the VT2W control related to humidity, operation, and maintenance.
Instructions for adjusting the Dehumidistat control to set desired indoor humidity levels for fall/winter/spring and summer.
Details on how to operate the 3-position switch for daily air supply adjustment and turning the unit off on specific models.
Instructions for using the 20-minute push-button timer for temporary high-speed air exchange.
Guide to operating the multi-minute push-button timer for timed air exchange sessions.
Details on how to activate and set the duration for the 60-minute crank timer.
Provides step-by-step instructions for performing quarterly maintenance, including cleaning filters and checking components.
Instructions for cleaning the condensation tray and inspecting the exterior air intake hood for obstructions.
Outlines the annual maintenance procedures, including cleaning the recovery core for both heat and heat/humidity recovery units.
Step-by-step guide to cleaning the centrifugal fan wheels, including disassembly and reassembly of the blower assembly.
Troubleshooting steps for when the outside temperature is not shown on the Platinum wall control display.
Instructions to contact the installer if error codes E1 or E3 appear on the Platinum or Deco-Touch wall controls.
Steps to check power, reset the unit, and contact installer for non-operational units or flashing indicators.
Troubleshooting tips for noisy units, excessive humidity, and window condensation, including control adjustments.
Advice for addressing dry indoor air or cold supply air, including control adjustments and system checks.
General| Type | Heat Recovery Ventilator |
|---|---|
| Airflow Capacity | 200 CFM |
| Airflow @ 0.2 in. w.g. | 200 CFM |
| Voltage | 120 V |
| Frequency | 60 Hz |
| Motor Type | PSC |
| Defrost Control | Automatic |
| Housing Material | Galvanized Steel |
| Duct Size | 6 in |
| Core Type | Crossflow |
