Why does my Bromic Heating TUNGSTEN 300-BURNER smell like gas?
If you notice a gas odor coming from your Bromic Heating Gas Heater, it could be due to several reasons. Check all pipe connections with a soap solution and tighten any loose connections. If the odor persists, the regulator, manual shut-off valve, or gas control valve might be defective and require replacement. Also, ensure the flexible hose is tightened.
How to fix a Bromic Heating Gas Heater that will not turn on?
If your Bromic Heating Gas Heater won't turn on, there could be a few potential causes. First, have an authorized electrician check the power supply. Second, have an authorized gas fitter check the gas supply. Finally, the control module may be in Lock-out mode; in that case, reset the Honeywell Lock-out.
Why does my Bromic Heating TUNGSTEN 300-BURNER Gas Heater turn on and off?
If your Bromic Heating Gas Heater turns on but then cycles on and off, it could be due to a few reasons. The flame on the ionization rod may be insufficient, so check and set the gas pressure and clear any obstruction to the burner venturi and injectors. Drafty conditions can also cause this issue, so discontinue use in high winds. Lastly, an insufficient earth connection between the heater and control box could be the problem; replace the wiring harness and clean connections to ensure a good earth.
What to do if there is carbon formation on my Bromic Heating TUNGSTEN 300-BURNER Gas Heater?
If you observe carbon formation on the ceramic tile surface of your Bromic Heating Gas Heater's burner, it could be due to several factors. The orifice might be misaligned, so consult your sales agent or the factory. There could be an obstruction in the venturi tube, so clean it with a bottle brush. Low gas pressure could also be the cause, so provide the required pressure. Finally, ensure the correct type of gas is supplied to the heater by checking the label.
What to do if my Bromic Heating TUNGSTEN 300-BURNER has no gas?
If there is no gas supply to your Bromic Heating Gas Heater, it could be due to several reasons. There might be air in the gas line, so purge the line. The manual shut-off valve may be closed, so open the valve. The regulator might be sticking, in which case, replace it. Alternatively, the regulator could be reversed, so remove it and install it properly.
Why is my Bromic Heating TUNGSTEN 300-BURNER Gas Heater burning gas inside the burner casting?
If the gas/air mixture is burning inside the burner casting of your Bromic Heating Gas Heater (flashback), it may be because of separation or cracks in the ceramic tiles, in which case, replace the burner assembly. The heater might also be mounted at an incorrect angle, so check the angle of the heater against the nameplate. Excessive drafts can also cause this, so shield or relocate the heater.
Why is the ceramic tile surface temperature low on my Bromic Heating TUNGSTEN 300-BURNER?
If your Bromic Heating Gas Heater has a low ceramic tile surface temperature, it could be due to several reasons. Low manifold gas pressure could be the cause. Low gas inlet pressure can also cause this issue, so clean the orifice. If the orifice is partially blocked with foreign matter, provide adequate ventilation of by-products. A misaligned manifold due to excessive torque on the pipe during installation can also cause this; replace the manifold. If the gas supply piping is too small, increase the gas pressure or replace the piping. Finally, remove any foreign matter in the venturi tube with a bottle brush.
Why is the control assembly of my Bromic Heating TUNGSTEN 300-BURNER overheating?
If the control assembly of your Bromic Heating Gas Heater is overheating, ensure the heater is mounted correctly. Mount the wall bracket/control housing against a vertical flat surface, following the instructions in the installation section of this manual. Always use supplied parts to mount the heater.
Details technical specifications for Tungsten Smart-Heat 300 and 500 models.
Details the gas type and inlet pressure requirements for the heaters.
Details the step-by-step process for installing the heater unit.
Verifies and adjusts the gas pressure for correct appliance operation.
General| Model | TUNGSTEN 300-BURNER |
|---|---|
| Brand | Bromic Heating |
| Category | Gas Heater |
| Material | Stainless Steel |
| Burner Material | Ceramic |
| Application | Outdoor |
| Fuel Type | Natural Gas / Propane |
| Gas Connection | 1/2" BSP |
| Warranty | 1 Year |
To Next Page
