Bromic Heating Tungsten Smart-Heat

Other manuals for Bromic Heating Tungsten Smart-Heat

Installation, Instruction And Service Manual26 pages

Questions and Answers

J
Jose WangAug 20, 2025
What to do if my Bromic Heating Heater burner will not light?
- A
  Austin SmithAug 20, 2025
  If the burner of your Bromic Heating Heater won't light, there could be several reasons. The gas valve might be off, so turn it on. The tank fuel may be empty, so replace the cylinder with a new one. There might be a blockage, or loose connections, so check all fittings. Other potential causes include low gas pressure, a bad thermocouple, or the heater not being in the correct location.
R
Rebecca GallowayAug 22, 2025
Why does my Bromic Heating Heater burner flame go out?
- M
  Michael SawyerAug 22, 2025
  If the burner on your Bromic Heating Heater won't stay on, it could be due to loose connections, so tighten them and check connections. It may also be caused by a bad thermocouple, a gas leak in the line, lack of fuel pressure, or the tank being nearly empty.
K
Kristen CurtisAug 25, 2025
What to do if my Bromic Heating Heater is producing thick black smoke?
- K
  kleinmariaAug 25, 2025
  If your Bromic Heating Heater is producing thick black smoke, there may be a blockage in the burner. Turn off the heater and let it cool. Remove the blockage and clear the burner inside and outside.
A
Angela CaseyAug 26, 2025
Why is the flame low on my Bromic Heating Heater?
- A
  Anne MillerAug 26, 2025
  If the burner flame is low on your Bromic Heating Heater, the supply hose may be bent or twisted. Straighten the hose and perform a leak test on it.
A
Allen ReedAug 28, 2025
What to do if the emitter glows unevenly on my Bromic Heating Heater?
- M
  Mary FarrellAug 28, 2025
  If the emitter glows unevenly on your Bromic Heating Heater, it could be due to low gas pressure, so replace the cylinder with a new one. Another reason may be that the base is not on a level surface, so place the heater on a level surface.
N
Nathan EsparzaAug 30, 2025
What to do if my Bromic Heating Control Unit does not receive signals from the remote?
- S
  Sarah ThorntonAug 30, 2025
  If the Bromic Heating Control Unit isn't responding to the remote, first, replace the remote's battery with a CR2430. If that doesn't work, the control box memory might be full; try deleting a remote from its memory. Finally, ensure the remote is correctly programmed into the control box.
C
Caitlin MerrittAug 31, 2025
How to fix a Bromic Heating Gas Heater that will not turn on?
- F
  feliciaphillipsSep 1, 2025
  If your Bromic Heating Gas Heater won't turn on, there are several potential causes. First, there might be no power supply; in this case, have an authorized electrician check the power. Second, there might be no gas supply; have an authorized gas fitter check the gas supply. Third, the control module might be in Lock-out mode; if so, reset the Honeywell Lock-out.
A
Aaron BryantSep 2, 2025
Why does my Bromic Heating Gas Heater smell like gas?
- A
  Alison CollierSep 2, 2025
  If you notice a gas odor coming from your Bromic Heating Gas Heater, it could be due to several reasons. It may be caused by a loose pipe connection, so check all connections with a soap solution and tighten where necessary. The regulator could also be defective, in which case it should be replaced. Other potential causes include a defective manual shut-off valve (replace it), a defective gas control valve (replace it), or a loose flexible hose (tighten it).
B
Benjamin SchneiderSep 4, 2025
What to do if my Bromic Heating Gas Heater has no gas?
- V
  Veronica SmithSep 4, 2025
  If there is no gas in your Bromic Heating Gas Heater, it could be due to several reasons: there might be air in the gas line, so you should purge the line. It's also possible that the manual shut-off valve is closed, so open the valve. Another potential cause is a regulator sticking, in which case you should replace the regulator. Finally, the regulator may be reversed; remove it and install it properly.
J
Jennifer MeltonSep 6, 2025
Why does my Bromic Heating Tungsten Smart-Heat Gas Heater turn on and off?
- C
  Christopher RamirezSep 6, 2025
  If your Bromic Heating Gas Heater turns on but then cycles on and off, several issues could be responsible. One potential cause is insufficient flame on the ionization rod; in this case, check and set the gas pressure and clear any obstruction to the burner venturi and injectors. Another cause may be drafty conditions; discontinue use in high winds. Also, there could be insufficient earth connection between heater and control box, so replace the wiring harness and clean connections to ensure a good earth.

Summary

Important Safety Information

General Safety Warnings and Precautions

Covers warnings about reading the manual, proper usage, electrical safety, installation by licensed technicians, and handling precautions.

Important Notes and Warnings

General Safety Warnings

Covers safety precautions for using the controller, including risks of fire, shock, and injury, and environmental considerations.

Installation Requirements

Details requirements for safe and compliant installation, including licensed installers, local codes, and protected cabling.

Maintenance and Repair Guidelines

Outlines procedures for maintenance, repair, and disposal, emphasizing qualified personnel and proper recycling.

Electrical Connection Specifications

Specifies requirements for electrical connections, including voltage, earth connection, safety devices, and wiring separation.

Product Overview

Description and Features

Details the Wireless Dimmer's suitability for heaters, power output control, voltage compatibility, and key features like dimming.

Kit Contents

Lists the items included in the product package, such as the wireless dimmer and remote control.

Installation and Safety Information

Provides initial safety warnings for operation and installation, emphasizing user responsibility and suitability checks.

Installation Steps

Outlines the sequential steps required for installing the wireless dimmer, from opening the box to refitting the cover.

Operation and Remote Control

Programming of 7-channel Remote

Details the process for programming a 7-channel remote to control the dimmer, including button presses and confirmation sounds.

Programming of 4-channel Remote

Explains how to program a 4-channel remote, including preset values for channels like brightness and power.

Copying Remote Functions

Describes how to copy an existing remote's programmed functions to a new remote for seamless transfer.

Deleting a Remote

Provides instructions for deleting a specific remote from the controller's memory, indicated by sound cues.

Technical Specifications

Wireless Controller Specifications

Lists key technical details including power supply, max output power, fuse protection, reception frequency, and dimensions.

Wiring Diagram

Controller Wiring Connections

Illustrates the internal connections for power supply, load, safety, and optional inputs, with status indicator explanations.

Bromic Heating Tungsten Smart-Heat Specifications

General

Heating Method	Radiant
Fuel Type	Natural Gas or Propane
Material	Stainless Steel
Application	Outdoor
Ignition Type	Electronic
Mounting Options	Wall or Ceiling Mount
Warranty	1 Year