Why my Brother JK1700 does not work?
If your Brother Sewing Machine isn't working, first, ensure that the main power switch is turned on. Also, check if the bobbin-winder shaft is pushed to the right; if it is, move it to the left. Finally, make sure you are using the foot controller properly.
Why is my Brother JK1700 skipping stitches?
If your Brother Sewing Machine is skipping stitches, first ensure that the upper thread is threaded correctly. Next, check that you are using the right combination of fabric, thread, and needle. If the needle is bent or blunt, replace it. Also, make sure the needle is correctly installed. Finally, remove the needle plate and clean the plate and the bobbin case to eliminate any accumulated dust.
Why does the upper thread break on my Brother Sewing Machine?
If the upper thread keeps breaking on your Brother Sewing Machine, here are a few things to check: * Ensure that the upper thread is threaded correctly. * Make sure there are no knots or tangles in the thread; if there are, remove them. * Verify that the needle is appropriate for the thread you are using; if not, choose an appropriate needle. * Check the upper thread tension; if it's too tight, loosen it.
How to fix thread tension on Brother JK1700?
If the thread tension is incorrect on your Brother Sewing Machine, consider the following: * Ensure the upper thread is threaded correctly. * Wind the bobbin thread properly. * Use the right combination of thread and needle for the fabric you're using. * Attach the presser foot holder properly. * Adjust the tension of the upper thread. * Use a bobbin designed for your machine. * Reset the bobbin thread correctly.
What to do if lower thread is tangled or breaks on Brother Sewing Machine?
If the lower thread of your Brother Sewing Machine is tangled or breaks, make sure that you have wound the bobbin thread properly. Also, the bobbin should not be scratched and turn smoothly, replace it if needed. Remove any tangled thread and clean the race. Ensure that you are using a bobbin that has been designed for this machine and that the bobbin is set correctly.
What to do if the fabric does not feed on my Brother JK1700 Sewing Machine?
If the fabric does not feed through your Brother Sewing Machine, first check if the darning plate is fitted on the needle plate and remove it. Also, ensure you are using the right combination of fabric, thread, and needle. Remove any tangled thread, especially in the race, and clean the race if necessary. Lastly, verify that the presser foot you are using is appropriate for the type of stitch you want to sew.
Why is the fabric wrinkled when sewing with my Brother JK1700 Sewing Machine?
If the fabric is wrinkling while using your Brother Sewing Machine, make sure that the upper thread is threaded properly and the bobbin is fitted correctly. Also, ensure that the spool is fitted properly and that you are using the right combination of fabric, thread, and needle. If the needle is bent or blunt, replace it. For thin fabrics, sew with stabilizer material under the fabric. Ensure the presser foot is appropriate for the stitch and adjust the upper thread tension if needed.
What to do if stitch is not sewn correctly on Brother JK1700?
If the stitch is not sewn correctly on your Brother Sewing Machine, make sure that you are using the correct presser foot for the type of stitch. Also, adjust the tension of the upper thread. If the thread is tangled, remove the tangled thread and clean the bobbin case if necessary.
What to do if fabric being sewn with Brother JK1700 cannot be removed?
If fabric being sewn with your Brother Sewing Machine cannot be removed, lift up the fabric and cut the threads below it. Then, clean the race.
Why does the needle keep breaking on my Brother JK1700?
If the needle on your Brother Sewing Machine breaks, consider these potential causes: * The needle may be incorrectly installed: Correctly install the needle. * The needle clamp screw might be loose: Use the oval screwdriver to firmly tighten the screw. * The needle could be bent or blunt: Replace the needle. * The upper thread may not be threaded correctly: Correct the upper threading. * The combination of fabric, thread, and needle may not be right: Choose a thread and needle appropriate for the fabric type. * The presser foot may not be appropriate for the stitch: Attach the correct presser foot. * The upper thread tension could be too tight: Loosen the upper thread tension. * You might be pulling the fabric too much: Lightly guide the fabric. * The spool may not be f...
General| Type | Mechanical |
|---|---|
| Stitches | 17 |
| Buttonhole Styles | 1 |
| Buttonhole Type | 4-Step |
| Max Stitch Width | 5 mm |
| Max Stitch Length | 4 mm |
| Free Arm | Yes |
| Needle Threader | Yes |
| Built-in Stitches | 17 |
| Included Accessories | Buttonhole foot, Zipper foot, Button sewing foot, needle set, bobbins, screwdriver, seam ripper, extra spool pin |
To Next Page
