BRP Evinrude E-TEC G2 User Manual

23
22––SSTTRROOKKEE EENNGGIINNEE OOIILL RREEQQUUIIRREEMMEENNTTSS
NNOOTTIICCEE
WWhheenn ooppeerraattiinngg iinn ccoonnddiittiioonnss
uunnddeerr 3322°°FF ((00°°CC)),, EEvviinnrruuddee XXPPSS
MMaarriinnee XXDD110000™™ ooiill mmuusstt bbee uusseedd..
EEvviinnrruuddee OOiill BBrraannddss
Evinrude XPS Marine XD 2– stroke
outboard oils are formulated to give
best engine performance while con-
trolling piston and combustion cham-
ber deposits, providing superior
lubrication, and ensuring maximum
spark plug life.
The following 2– stroke outboard oils
are recommended for use in your
Evinrude E-TEC outboard:
– Evinrude XPS Marine XD100™ Di-
rect Injection Oil
– Evinrude XPS Marine XD50™ 2–
Stroke Oil
– Synthetic TC-W3 NMMA-certified
oil
Evinrude XPS Marine XD100™ oil is
preferred for your
Evinrude E-TEC
outboard. This synthetic formula oil
provides uncompromised lubrication
and superior performance, even in ex-
treme conditions especially in cold
temperatures down to 0°F (-17°C).
NNOOTTIICCEE
DDOO NNOOTT aadddd aauuttoommoottiivvee ttyyppee 44––
ssttrrookkee ooiillss ttoo 22––ssttrrookkee eennggiinnee ooiill
ttaannkk((ss)).. DDoo nnoott aadddd ooiill ttoo tthhee ffuueell..
Failure to follow oil specifications
could void the engine warranty if a lu-
brication-related failure occurs.
OOiilliinngg SSyysstteemm IInnffoorrmmaattiioonn
If a “LOW OIL” warning occurs, you
have a limited amount of time of nor-
mal operation before running out of
oil. Refill the oil tank with approved oil
as soon as possible.
Refer to
EENNGGIINNEE MMOONNIITTOORRIINNGG .
To check oil level:
– Trim the outboard to the vertical
position.
– Use a digital display or gauge to
check the oil tank level.
Always “top off” your oil tank prior to
prolonged usage or long trips. You
may want to keep an extra supply of
outboard oil in the boat.
New outboards are programmed to
use additional oil during the first two
hours of operation above 2000 RPM.
If you run the oil tank empty, REFILL
the oil tank and prime the oil system
before using the engine. Refer to
FILLING THE ON-ENGINE OIL TANK
and PRIMING THE OIL SYSTEM .
If an accessory remote oil tank is in-
stalled and the oil hose is discon-
nected for any reason, seal it to
prevent spillage. Install a cap on the
hose fitting to prevent contamination.
OOiill TTaannkk CCaappaacciittyy
The on-engine oil tank capacity is 1.9
gallons (7.2 Liters)
OOppttiioonnaall RReemmoottee OOiill TTaannkk
The following optional accessory re-
mote oil tank kits are available:
– 1.8 gallons (6.8 liters)
– 3.0 gallons (11.3 liters)
– An oil tank pick-up kit is also avail-
able for the 10 gallon (37.8 liters)
capacity oil tank.
Install the optional remote oil tank fol-
lowing the instructions provided with
the unit.
FFiilllliinngg tthhee OOnn EEnnggiinnee OOiill TTaannkk
1. Remove the top cap of the engine
cover.
2. Remove the oil fill cap.
3. Fill the oil tank with outboard lubri-
cant. Oil capacity is 1.9 gallons
(7.2 Liters).

BRP Evinrude E-TEC G2 Specifications

General

Brand	BRP
Model	Evinrude E-TEC G2
Category	Outboard Motor
Language	English