BRP Evinrude E-TEC G2 User Manual

24
4. Replace the filler cap and tighten
securely.
If you run the tank empty, you must
prime the oil system before using the
engine.
1
2
010842-1
OOIILL FFIILLLL CCAAPP
1. Oil Fill Cap
2. Oil Fill Tube
TTiipp
If the low engine oil light is illuminated,
a full gallon of engine oil may be
added to the reservoir.
PPrriimmiinngg tthhee OOiill SSyysstteemm
The oil system of Evinrude E-TEC out-
boards is primed at the factory.
Priming the oil system is only required
if:
– The oil system is disassembled for
service or parts replacement
– The oil tank is run out of oil
NNOOTTEE:: If the oil tank is run out of oil,
the
EMM will activate SHUT DOWN
mode and set Fault Code 33. See
NO
OIL
.
After refilling an empty oil tank or serv-
icing the oil system, air MUST be re-
moved from the oil system before
operating the outboard.
Prime the oil system by performing
the
LONG-TERM STORAGE (WIN-
TERIZATION)
— TWO times.
If available,
Evinrude Diagnostic soft-
ware v 6.1 or higher may be used to
prime the oil system ONE time.
FFuueell RReeqquuiirreemmeennttss
WWAARRNNIINNGG
GGaassoolliinnee iiss eexxttrreemmeellyy ffllaammmmaabbllee
aanndd hhiigghhllyy eexxpplloossiivvee uunnddeerr cceerrttaaiinn
ccoonnddiittiioonnss.. FFoollllooww tthhee iinnssttrruuccttiioonnss
iinn tthhiiss sseeccttiioonn eexxpplliicciittllyy.. IImmpprrooppeerr
hhaannddlliinngg ooff ffuueell ccoouulldd rreessuulltt iinn
pprrooppeerrttyy ddaammaaggee,, sseerriioouuss iinnjjuurryy
oorr ddeeaatthh..
LLeeaakkiinngg ffuueell iiss aa ffiirree aanndd eexxpplloo--
ssiioonn hhaazzaarrdd.. AAllll ppaarrttss iinn tthhee ffuueell
ssyysstteemm sshhoouulldd bbee iinnssppeecctteedd ffrree--
qquueennttllyy aanndd rreeppllaacceedd iiff ssiiggnnss ooff
ddeetteerriioorraattiioonn oorr lleeaakkaaggee aarree
ffoouunndd.. IInnssppeecctt tthhee ffuueell ssyysstteemm
eeaacchh ttiimmee yyoouu rreeffuueell,, eeaacchh ttiimmee
yyoouu rreemmoovvee tthhee eennggiinnee ccoovveerr aanndd
aannnnuuaallllyy..
NNOOTTIICCEE
AAllwwaayyss uussee ffrreesshh ggaassoolliinnee.. GGaassoo--
lliinnee wwiillll ooxxiiddiizzee;; tthhee rreessuulltt iiss lloossss
ooff ooccttaannee,, vvoollaattiillee ccoommppoouunnddss,,
aanndd tthhee pprroodduuccttiioonn ooff gguumm aanndd
vvaarrnniisshh ddeeppoossiittss wwhhiicchh ccaann ddaamm--
aaggee tthhee ffuueell ssyysstteemm..
Fuel blending varies by country and
region. Your outboard has been de-
signed to operate using the recom-
mended fuels; however, be aware of
the following:
– The boat’s fuel system may have
different requirements regarding
the use of alcohol fuels. Refer to
the boat’s owner guide.
– Alcohol blended fuels attract and
hold moisture which may lead to
fuel phase separation and can re-
sult in engine performance prob-
lems or engine damage.
– Use of fuel containing alcohol
above the percentage specified by
government regulation can result
in the following problems in
2–STROKE ENGINE OIL REQUIREMENTS

BRP Evinrude E-TEC G2 Specifications

General

Brand	BRP
Model	Evinrude E-TEC G2
Category	Outboard Motor
Language	English