EasyManuals Logo

BRP Evinrude E-TEC G2 User Manual

BRP Evinrude E-TEC G2
82 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #38 background imageLoading...
Page #38 background image
38
NNOOTTIICCEE
TThhee oouuttbbooaarrddss sshhoocckk aabbssoorrppttiioonn
ssyysstteemm ddooeess nnoott wwoorrkk wwhhiillee ooppeerr--
aattiinngg iinn rreevveerrssee.. IIff yyoouu bbaacckk iinnttoo
aann oobbjjeecctt,, eeiitthheerr iinn tthhee wwaatteerr oorr
wwhhiillee ttrraaiilleerriinngg,, yyoouurr bbooaatt aanndd oouutt--
bbooaarrdd ccaann bbee sseerriioouussllyy ddaammaaggeedd..
If you hit any object:
STOP immediately and examine
the outboard for loosening of at-
taching hardware.
INSPECT for damage to swivel
and stern brackets, and steering
components.
EXAMINE the boat for structural
damage.
TIGHTEN any loosened hardware.
If the collision occurred in the water,
proceed slowly to harbor. Before boat-
ing again, have your Dealer thor-
oughly inspect all components.
If your engine will not trim to the fully
DOWN position, it may have impacted
an underwater object. See the
SERV-
ICE NOTE
.
WWAARRNNIINNGG
FFaaiilluurree ttoo iinnssppeecctt ffoorr ddaammaaggee
aafftteerr aann aacccciiddeenntt oorr ssttrriikkiinngg aann oobb--
jjeecctt ccoouulldd rreessuulltt iinn ssuuddddeenn,, uunneexx--
ppeecctteedd ccoommppoonneenntt ffaaiilluurree,, lloossss ooff
bbooaatt ccoonnttrrooll,, aanndd ppeerrssoonnaall iinnjjuurryy..
IIggnnoorreedd ddaammaaggee ccoouulldd rreedduuccee
yyoouurr bbooaatt aanndd oouuttbbooaarrddss aabbiilliittyy ttoo
rreessiisstt ffuuttuurree iimmppaaccttss..
DDyynnaammiicc PPoowweerr SStteeeerriinngg ((DDPPSS))
Your outboard may be equipped with
Dynamic Power Steering (DPS). DPS
offers three power steering assist
levels.
PPoowweerr SStteeeerriinngg AAssssiisstt LLeevveellss
All power steering assist levels pro-
vide the same rate of assist at engine
speeds below 4500 RPM.
As engine speed increases above
4500 RPM, assist levels progressively
decrease.
The factory default assist level is “Min-
imum”. Use the
Evinrude ICON-Touch
or
ICON-CS
digital display to change
the power steering assist level to “Me-
dium” or “Maximum”.
WWAARRNNIINNGG
SSeelleeccttiioonn ooff ppoowweerr sstteeeerriinngg aassssiisstt
lleevveell iiss aa mmaatttteerr ooff ooppeerraattoorr
pprreeffeerreennccee..
BBee aawwaarree tthhaatt cchhaannggiinngg tthhee ppoowweerr
sstteeeerriinngg aassssiisstt lleevveell ccaann aaffffeecctt
bbooaatt hhaannddlliinngg..
AAfftteerr cchhaannggiinngg tthhee lleevveell ooff ppoowweerr
sstteeeerriinngg aassssiisstt,, ooppeerraattee tthhee bbooaatt
wwiitthh ccaarree ttoo bbeeccoommee ffaammiilliiaarr wwiitthh
aannyy cchhaannggeess iinn bbooaatt hhaannddlliinngg
cchhaarraacctteerriissttiiccss..
If your boat is not equipped with an
ICON
-digital display, your Dealer must
use
Evinrude Diagnostic
software to
change the power steering assist
level.
OPERATION

Other manuals for BRP Evinrude E-TEC G2

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the BRP Evinrude E-TEC G2 and is the answer not in the manual?

BRP Evinrude E-TEC G2 Specifications

General IconGeneral
BrandBRP
ModelEvinrude E-TEC G2
CategoryOutboard Motor
LanguageEnglish

Related product manuals