Appendix D: REACTION 54 COMPLETE PARTS LIST
Some parts may be stuck together with a spray adhesive used in manufacturing. They should be easy to pry apart. Sand them lightly to remove residue.
BALSA STICKS FUSELAGE PARTS BAG
4 3/32 x 3/8 x 36 Balsa 2 5/16 x 2-1/2 x 2-1/2 Balsa Servo Mount Braces (big triangles)
4 3/16 x 3/8 x 36 Balsa Trailing Edge Spars 2 1/8 x 1-5/8 x 2-3/4 Lite-Ply
3 5/16 x 5/16 x 36 Balsa 2 1/8 x 2-1/4 x 3-5/8 Lite-Ply
1 5/16 x 1/2 x 36 Balsa Fin Posts, Temporary Braces 1 1/8 x 2 x 3-1/2 Lite-Ply H-2 Hatch Bulkhead
1 1/4 x 1 x 36 Balsa Wiring Rack, Tank Rails, Tube Guides 1 1/8 x 1-5/8 x 2-1/2 Lite-Ply F-1
1 3/8 x 3/8 x 36 Balsa Stabilizer Leading Edge 1 1/8 x 4-1/2 x 6-7/8 Lite-Ply F-3 & H-3 (to be separated by builder)
2 3/8 x 3/8 x 36 Balsa Shaped Leading Edges 1 1/8 x 5 x 8 Lite-Ply F-4 & H-4 (to be separated by builder)
2 1/2 x 9/16 x 24 Balsa Shaped Trailing Edges - Outboard 1 1/8 x 5 x 8-3/8 Lite-Ply F-5
2 1/2 x 11/16 x 24 Balsa Shaped Trailing Edges - Inboard 2 1/8 x 1-3/4 x 5 Lite-Ply
4 1/2 Triangle x 36 Balsa Corner Reinforcements 1 1/8 x 5 x 5-1/2 Lite-Ply F-6
2 1/2 Triangle x 36 Balsa Corner Reinforcements (trimmed edge) 1 1/8 x 1-1/2 x 4-3/8 Lite-Ply F-7 Front Turbine Mount Bulkhead
1 3/4 Triangle x 18 Balsa Landing Gear Mount Reinforcements 1 1/8 x 1-1/2 x 3-7/8 Lite-Ply
1 1/8 x 2-1/2 x 4-3/4 Lite-Ply Servo Mount
HARDWOOD STICKS
1 1/8 x 2-1/2 x 3 Lite-Ply Servo Mount Doubler
2 1/8 x 3/8 x 12 Lite-Ply Reinforcements 2 1/8 x 2 x 3 Lite-Ply Hatch Tongues
2 1/4 x 3/8 x 12 Bass Servo Rails, Rear Hatch Rails, J-Bolt Pads 1 1/8 x 3-3/4 x 4-1/4 Lite-Ply Receiver Shelf
4 1/4 x 1/2 x 36 Spruce Top Main Spar, Top & Bottom Stub Spar 1 1/8 x 3-7/8 x 4-3/4 Lite-Ply ECU Shelf
2 1/4 x 1/2 x 36 Spruce Bottom Main Spar (beveled edge) 1 1/8 x 5 x 8-7/8 Lite-Ply Tank Compartment Top
2 1/4 x 1/2 x 12 Spruce Top Main Spar Doubler 1 1/32 x 1/2 x 1 AC Ply Rear Hatch Tab
2 1/4 x 1/2 x 12 Spruce Bottom Main Spar Doubler (beveled edge) 1 3/32 x 4-1/4 x 5 AC Ply Turbine Mount
2 3/16 x 5/8 x 1-1/4 AC Ply Latch Retainers (grooved edge)
BALSA SHEETS
1 3/16 x 1-1/2 x 4 AC Ply Turbine Mount Doubler
6 3/32 x 3 x 36 Balsa Trailing Edge Sheeting, Shear Webs 1 1/4 x 1/2 x 3 AC Ply H-1 Front Hatch Bulkhead
6 3/32 x 4 x 7-1/2 Balsa Wingtip Sheeting, Fuselage Sheeting 1 1/4 x 1-1/2 x 3-1/2 AC Ply F-2 Nose Retract Mount
18 3/32 x 4 x 36 Balsa LE & Center Sheeting, Fuselage Sheeting 1 3/8 x 1-1/2 x 2-3/8 AC Ply Wing Mount
4 1/4 x 4 x 36 Balsa Fuselage Sheeting 1 3/8 x 3/4 x 1 Poplar
1 3/8 x 2 x 2 Poplar Thrust Wedge
WING RIBS
2 3/32 x 20-1/4 Balsa W-1 Wing Rib
WING PARTS BAG
2 3/32 x 19-3/4 Balsa W-2 Wing Rib 1 3/8 x 1-1/4 x 3 Balsa Material for Fuselage Fairing Sides
2 3/32 x 19 Balsa W-3 Wing Rib 2 1/8 x 4-1/2 x 5-1/2 Lite-Ply Wheel Well Frames and Floors
2 3/32 x 18-1/2 Balsa W-4 Wing Rib 4 1/8 x 2-1/4 x 5-1/2 Lite-Ply
2 3/32 x 17-3/4 Balsa W-5 Wing Rib 2 1/8 x 2-3/4 x 3-1/2 Lite-Ply
2 3/32 x 17 Balsa W-6 Wing Rib 2 1/8 x 2-3/8 x 3 Lite-Ply Flap Servo Mounts
2 3/32 x 16-1/4 Balsa W-7 Wing Rib 2 1/8 x 2-7/8 x 4 Lite-Ply Aileron Servo Mounts
2 3/32 x 15-1/2 Balsa W-8 Wing Rib 2 1/8 x 1/2 x 4-1/2 Lite-Ply Wing Hatch Rails
2 3/32 x 15-1/2 Balsa W-9 Wing Rib 2 1/8 x 2-1/2 x 3 Lite -Ply SWDG Shear Web / Dihedral Gauge
2 3/32 x 14-1/2 Balsa W-10 Wing Rib 1 1/8 x 1-1/2 x 5-1/2 Lite-Ply Fuselage Fairing Face Plate
2 3/32 x 13-3/4 Balsa W-11 Wing Rib 6 1/16 x 1 x 1 AC Ply Control Horn Pads
2 3/32 x 13 Balsa W-12 Wing Rib 1 3/32 x 15/16 x 2-1/4 AC Ply Wing Bolt Plate
2 3/32 x 12-3/8 Balsa W-13 Wing Rib 2 1/8 x 4-1/2 x 4-1/2 AC Ply Retract Mounts
2 3/32 x 12-1/4 Balsa W-14 Wing Rib 4 1/8 x 1/3/4 x 5-1/2 AC Ply
2 Birch Wing Dowels
Capstrips, Wiring Rack
D-1 Receiver Shelf Positioner
Longerons, Rudder Caps, Braces D-2 ECU Shelf Positioner
F-5D (doublers for F-5)
F-8 Rear Turbine Mount Bulkead
Pushrod Housing Clamp
W-6D Rib Doublers
Dowel Block Doublers (partial rib)
Retract Mount Doublers
1/4 dia. x 4
To Next Page
