REACTION 54 PARTS LIST - CONTINUED
MACHINED BALSA FUSELAGE PARTS HARDWARE
2 1/4 x 4 x 36 Balsa SIDE-1 (notched, left and right) 12 #2 x 3/8 Truss Head Steel Sheet Metal Screw (wing hatches)
2 1/4 x 1 x 10 Balsa SIDE-2 4 #2 x1/2 Pan Head Steel Sheet Metal Screw (rudder control horn)
2 1/4 x 4 x 36 Balsa SIDE-3 20 #2 x 3/4 Pan Head Steel Sheet Metal Screw (all other control horns)
2 1/4 x 2 x 19 Balsa SIDE-4 2 #4 x 3/4 Flat Head Steel Sheet Metal Screw (wire rack)
2 1/4 x 4 x 27 Balsa Hatch Side/SIDE-5 4 #6 x 1 Pan Head St Steel Sheet Metal Screw (turbine mount)
1 1/4 x 3 x 13-1/2 Balsa Stabilizer Mount 6 4-40 Steel Hex Nuts (use for clevis jam nuts)
1 2-1/4 x 3 x 3 Balsa Nose Block 2 1/4 -20 x 3 Rd Head Alum Wing Bolts (may be shortened to 2.5")
2 Nylon Flat Washers (for wing bolts)
MACHINED BALSA FIN/RUDDER PARTS
2 4-40 Steel Threaded Couplers (elevator, rudder)
1 5/16 x 3 x 10 Balsa FIN-1 6 4-40 Steel Solder Clevis (1 per control surface)
1 5/16 x 3 x 8-1/2 Balsa FIN-2 6 4-40 Steel Sure-Lock Clevis (1 per control surface)
1 5/16 x 3 x 6-3/4 Balsa FIN-3 6 3/16 x 1/4 Steel Locking Clips (1 per clevis)
1 5/16 x 3 x 5-1/4 Balsa FIN-4 3 Short (3/4") Steel Control Horns (2 flap, 1 rudder)
1 5/16 x 3 x 3-1/2 Balsa FIN-5 3 Long (1-1/8") Steel Control Horns (2 aileron, 1 elevator)
1 5/16 x 3 x 1-3/4 Balsa FIN-6 6 5/8 x 7/8 Nylon Control Horn Backing Plates
1 5/16 x 2 x 25 Balsa FIN-7 Fin Front 1 5/8 x 1-7/8 Metal Hatch Latch (assembled)
1 5/16 x 3 x 10-3/8 Balsa Rudder (tapered and beveled) 4 4-40 x 6 Steel Threaded Rod (2 aileron, 2 flap)
8 5/8" Brass Cup Hooks (4 rear hatch, 4 hold downs)
MACHINED BALSA STAB/ELEVATOR PARTS
1 Rubber Grommet (for turbine wiring at fuselage)
2 3/8 x 2-1/4 x 5 Balsa STAB-1 20 #10 Rubber Rubber Bands (wire rack, rear hatch)
1 3/8 x 2-3/4 x 22 Balsa STAB-2 32 3/4 x 1 Secret
3 3/8 x 2-3/4 x 26 Balsa STAB-3
2 3/8 x 2-2/4 x 9-1/2 Balsa STAB-4 Stabilizer Tips
MISCELLANEOUS
1 3/8 x 2-1/4 x 26 Balsa Elevator (tapered and beveled) 4 36 x 48 Paper Full-Size Plans - Wing Panels, Fuselage
1 24 x 36 Paper Full-Size Plan - Stabilizer
MACHINED BALSA WING PARTS
1 40 Pages Paper Instruction Book with Color Photos
2 1 x 2-1/2 x 3 Balsa Wing Dowel Supports 3 8-1/2 x 14 Paper Servo Lead Tubes
1 1 x 3 x 4 Balsa Wing Bolt Supports 1 60 oz. Nylon Du-Bro Fuel Tank (with hardware)
2 1-1/2 x 2 x 15-1/2 Balsa Wingtips 1 3/16 x 3 x 3 Foam Fuel Tank Pad - Front
2 5/8 x 2-1/2 x 6 Balsa Tip TE Extensions (tapered) 1 1/2 x 4-3/4 x 9 Foam Fuel Tank Pad - Top
1 5/8 x 2-1/2 x 30 Balsa Ailerons (tapered and beveled) 1 .003 x 6 x 8 St Steel Heat Shield Material
2 3/4 x 3 x 3-1/2 Balsa Root TE Extensions (tapered) 1 1-1/2 x 10 Alum Tape (to finish edge of heat shield)
1 3/4 x 3 x 32-1/2 Balsa Flaps (tapered and beveled) 1 2 x 56 Glass Fiberglass Tape (for wing center joint)
1 1-3/4 x 16 Vinyl Graphic - Reaction 54 Logo (black)
LOOSE PLYWOOD PARTS
1 2-1/2 x 9 Vinyl Graphic - BTE Logos (black)
2 1/8 x 7-1/4 x 35 Lite-Ply 1 Steel
2 1/8 x 3-3/4 x 10 Lite-Ply Boat Tail Sides 1 Nylon Cable Housing (nylon tube)
2 1/8 x 5-1/4 x 9-1/2 Lite-Ply Boat Tail Formers 1 4-1/4 x 11 Paper Template Sheet (blue card stock)
1 1/8 x 2-3/4 x 9-1/2 Lite-Ply Boat Tail Jig 1 .090 Alum Turbine Mounting Bracket*
2 1/32 x 1-7/8 x 12 AC Ply Wheel Well Liner
1 1/4 x 2 x 10 AC Ply Rear Dihedral Brace *Several Styles Available to Suit Different Turbines
1 1/4 x 2 x 15 AC Ply Front Dihedral Brace
1/4 i.d. x 3/4 o.d.
1/2" i.d. x 1" o.d.
Sig Easy Hinges (one extra)
Fuselage Doublers 3/32 dia. x 98 Stranded Cable (elev & rud linkage)
3/16 o.d. x 98
To Previous Page
