What does incomplete communication with SAFe mean on Buderus Logano plus GB312 Boiler?
Incomplete communication with SAFe on your Buderus Boiler means that the MC10 is not receiving all required data from the SAFe. If connections are okay, replace the SAFe.
What to do if my Buderus Logano plus GB312 Boiler shows low water pressure?
If the water pressure is less than 8.7 psi (0.6 bar), you should adjust the operating pressure. Also, try switching the boiler OFF and then ON again using the controller.
What to do if my Buderus Logano plus GB312 is not detecting a flame within the safety period?
If no flame is detected within the safety period and the ionization current is less than 1.1 ?A, there might be a gas pressure issue. If the pressure is too low, contact your gas company.
What causes undervoltage in Buderus Logano plus GB312?
If the mains voltage is too low causing undervoltage in your Buderus Boiler, ensure the correct power supply.
What to do if Buderus Logano plus GB312 shows no speed signal?
If your Buderus Boiler shows 'no speed signal,' it means the SAFe is not receiving a speed signal even though the fan is supposed to be running. Establish good electrical contact to fix this.
How to troubleshoot an incorrect hydraulic connection of the Buderus Logano plus GB312 Boiler or pump?
If the Buderus Boiler control unit has recognised an incorrect flow on the water side due to an incorrect hydraulic connection of boiler or pump, check whether the boiler flow and return sensor have been swapped and check the pump for correct direction of flow. Also, connect flow and return correctly and ensure correct pump flow direction.
What to do if there is no gas pressure in my Buderus Logano plus GB312?
If your Buderus Boiler has no gas pressure, it's likely due to a simple cause: there is no gas pressure. The suggested solution is to turn on the gas cock if necessary.
Why has the Buderus Logano plus GB312 Boiler flow temperature reached its maximum permissible level?
The boiler flow temperature may have reached its maximum permissible level because the high temperature safety cut-out has tripped. To resolve this, check the gas valve.
What to do if the internal SAFe relay is faulty in Buderus Logano plus GB312?
If Internal SAFe electronics are faulty, press "Reset" and wait to see if the fault has been removed.
What does it mean if my Buderus Boiler has an incomplete communication with SAFe?
If the MC10 registers this fault because not all required data is supplied by the SAFe, and the connections are OK, replace the SAFe.
Provides guidance on how to best use the installation and maintenance instructions for safety.
Explains the intended purpose and application of the Buderus Logano plus GB312 boiler.
Defines the meaning of warning symbols, caution symbols, and user notes within the documentation.
Highlights critical safety instructions, including gas leak procedures and boiler room environmental advice.
Identifies and describes the main physical parts of the boiler, including the heat exchanger and casing.
Explains the functions of the various buttons, dials, and indicators on the BC10 control panel.
Provides step-by-step instructions for starting the heating system via the control panel and programming unit.
Details the procedure for safely shutting down the boiler and its components.
Outlines essential steps to take in case of emergencies like fire or flooding.
Advises on the frequency of checking operating pressure, especially after installation or over time.
Guides on how to read the pressure gauge and what action to take if pressure is low.
Details the process of filling the system with water and performing leak detection before operation.
Emphasizes using the specified fuel and maintaining a clean boiler room environment.
Highlights the benefits of regular maintenance for efficiency, reliability, and combustion quality.
Explains how to identify fault codes on the control panel and the procedure for resetting them.
Provides guidance on how to best use the installation and maintenance instructions for safety.
Explains the intended purpose and application of the Buderus Logano plus GB312 boiler.
Defines the meaning of warning symbols, caution symbols, and user notes within the documentation.
Highlights critical safety instructions, including gas leak procedures and boiler room environmental advice.
Identifies and describes the main physical parts of the boiler, including the heat exchanger and casing.
Explains the functions of the various buttons, dials, and indicators on the BC10 control panel.
Provides step-by-step instructions for starting the heating system via the control panel and programming unit.
Details the procedure for safely shutting down the boiler and its components.
Outlines essential steps to take in case of emergencies like fire or flooding.
Advises on the frequency of checking operating pressure, especially after installation or over time.
Guides on how to read the pressure gauge and what action to take if pressure is low.
Details the process of filling the system with water and performing leak detection before operation.
Emphasizes using the specified fuel and maintaining a clean boiler room environment.
Highlights the benefits of regular maintenance for efficiency, reliability, and combustion quality.
Explains how to identify fault codes on the control panel and the procedure for resetting them.
To Next Page
General