29
Step 3:
Remove the pleated cartridge(s) by turning the lter
core cap(s) counter clockwise then sliding the cartridge(s) upward
from the lter core.
Step 4: Using a garden hose with a nozzle or other high-
pressure device, clean cartridge(s). Work rst from the inside, top
to bottom on each pleat then from the outside, top to bottom on
each pleat.
• To remove collected lotions or body oils, soak cartridge(s) in
warm water with a Filter Cleaner or detergent.
• To remove calcium deposits, soak cartridge(s) in a plastic
container using a 1:10 ratio of Muriatic acid to water
solution. Calcium deposits indicate a high spa pH, which
should be corrected.
•
NOTE:
Filter(s) must be cleaned with a lter cleaner/
degreaser before attempting to remove calcium and mineral
deposits with any acidic based product
Step 5: Reinstall cartridges(s) by aligning the cartridge slot with
the lter core n; reinstall the lter core cap(s), lter plate, and
Filter SnapCap.
Step 6: Restore main power to the spa.
IMPORTANT: Using a brush to clean a lter cartridge could
cause damage to the lter media.
LED Light Replacement
Contact your authorized Bullfrog Spas Dealer for repair.
Spa Shell Care
e spa cover is an essential part of the spa system. It will both
protect the spa and to provide the highest possible eciency. To
ensure you have the best experience possible, ensure the cover is
in place except during spa use. e best protection for your comes
when the cover is on the spa with the skirt covering the entire
shell.
General Cleaning
For normal cleaning, use a mild dishwashing soap, window
cleaner, or other products recommended by your local authorized
Bullfrog Spas Dealer. For stubborn stains, use a mild acrylic
cleaner or a mild detergent. To apply these cleaners, use a soft,
damp cloth or sponge. Rinse well and dry with a clean cloth. To
clean hard water stains, remove light scratches and protect your
spa shell, contact your authorized Bullfrog Spas Dealer.
Cleaning the Scum Line
With normal use of the spa, oils, lotions, and hair products will
build up on the surface of the water. is will leave a scum line
around the perimeter. is can be easily removed using a spa
surface cleaner or its equivalent. Avoid using cleaning agents that
leave soap residue in the water.
WARNING: Never allow your spa surface to be exposed to
alcohol, acetone (nail polish remover), nail polish, dry cleaning
solution, lacquer thinners, gasoline, pine oil, abrasive cleaners,
or any other household chemicals other than those listed. ese
chemicals void the warranty.
Special Care For R Series Injection
Molded JetPaks
High levels of sanitizer and normal use over time can have a
bleaching eect on the injection molded (dark gray) Jetpaks.
ese can be cleaned / bued to look like new again with the
aid of automotive polishing compound found at any automotive
retailer. Simply use a soft towel to rub this compound onto the
plastic. en bu with a dry towel.
JetPak™ Plumbing Care
For optimum spa care, each time the spa water is changed,
remove all JetPaks. Clean the back manifold area on with a spa
surface cleaner and a long, soft bristle brush. For cleaning the
JetPak acrylic surface, refer to Spa Shell Care.
Spa Cabinet Care
e EternaWood™ cabinet components are made to provide
many years of maintenance-free service. For normal cleaning,
use a mild dishwashing soap. For stubborn stains, contact your
authorized Bullfrog Spas Dealer.
Spa Cover Care
Your spa cover is warranted by its manufacturer. Although basic
instructions are provided below, it is important that you refer to
the information that came with the cover. e manufacturer
provides detailed information on caring for your spa cover
and what to do to protect its warranty.
To Next Page
Loading...
