BullFrog A7L - R SERIES (R600) CONTROL PANELS (cont.); Stereo Controls and Bluetooth Pairing

21
use or temperature adjustments. is lock feature prevents most
functions on the controller from being used, while all automatic
functions remain active. “TEMP” locks the temperature selection,
preventing unwanted temperature adjustments . “PNL” in
contrast, locks all changes from the panel. Features will function
as selected.
To Lock Temperature or Panel
To lock the settings, press several times until “LOCK” is
displayed. Press
or to select the lock menu. “TEMP” will
display in the display window. Press Press , “OFF” will
display in the window. Press , or to select “ON.” Press
to conrm your selection. is will lock the temperature
settings. Follow the same process, and select “OFF” to turn o
the lock function.
To lock the panel, press several times until “LOCK” is
displayed. Press to select the lock menu. “TEMP” will
display. Next press and “PANL” will display in the window.
Press , “OFF” will ash in the display window. Press or
to change the setting to “ON.” Press to conrm the panel
lock.
To Unlock Temperature or Panel
Press and hold and simultaneously twice for about a
second each time. “UNLK” will display in the window and the
temperature or panel controls will return to normal.
NOTE: If both “PANL” and “TEMP” are locked, the unlock
procedure must be performed twice.
Filtration Cycles
Your R-Series Spa comes factory programmed to run two cycles
in each 24 hour period.
Filter Cycle 1: Begins at 6:00pm (18:00) and runs for 2 hours
for single pump spas and 3 hours for dual pump spas.
Filter Cycle 2: Begins at 8:00am (8:00) and runs for 1 hour
for both single pump and dual pump spas.
ese factory set ltration cycles should be adequate for light to
normal spa use (spas used once to twice per week). For cases of
more frequent, to heavy spa usage, you may need to increase the
lter cycle durations to maintain water clarity.
Changing Filter Cycles:
To change lter 1 cycle:
1. Press “MENU SELECT” button several times until
“FLTR1” appears on the display.
2. Press button, “BEGN” will appear. is indicates
Filter Cycle 1’s “begin time.”
3. Press button again. e hour digit will ash. Press
button or button to adjust hour. (NOTE: “A” for am
or “P” for pm will be displayed in the bottom right corner of
the display window).
4. Press
button. Minutes will be ash. Press button
or button to adjust duration of the pump cycle in 15
minute increments.
5. Press button to save your selection. “RUN HRS” will
appear. Press button to display Filter 1(“F1”) end time.
Push button to go to Filter 2.
To change lter 2 cycle:
1. Press button several times until “FLTR2” appears.
2. Press button to toggle between “ON” and “OFF”
(NOTE: Filter 2 cycle can be turned o. However, this is
not recommended and can lead to poor water clarity).
3. Press button. “BEGN” will appear. Press button,
hour will begin to ash. Press button or button to
adjust the starting time for Filter 2 ltration. (NOTE: “A”
for am or “P” for pm will be displayed in the bottom right
corner of the display window).
4. Press button. Minutes will begin to ash. Press
button or button to adjust duration of the pump cycle in
15 minute increments.
5. Press button to save your selection. “RUN HRS” will
appear. Press button to display Filter 2 (F2) end time.
Press button.
“LITE TIMR” is not functional in R-Series Spas.
To Change Preferences
Changing temp display between
Fahrenheit (F) and Celcius (C)
Press several times until “PREF” appears in the display
window. Press , “F/C” will appear. Press to conrm your
changes.
Changing 12 or 24 hour clock
Press several times until “PREF” appears in the display
window. Press , “F/C” will appear. Press , “24-12” will
display in window. Press , the current selection will ash.
Press until the desired setting is selected. Press to
conrm your selection.
Turning reminders OFF or ON
Press several times until “PREF” appears in the display
window. Press , “F/C” will appear. Press several times
until “RE-MIN-DERS” begins to scroll through the display.
Press , the current selection will begin to ash in the
window. Press to change to your desired selection. Press
to conrm your selection.
Set Cleanup Cycle
e cleanup cycle, is a maintenance cycle designed provide
additional circulation and ltration between regular lter cycles.
It runs 30 minutes after each spa use.
To adjust the duration of the
cleanup cycle:
Press several times until “PREF” appears in the display