Burmester 232 - User Manual

This operation manual describes how to start up the Burmester
232 integrated amplifier.
More information about the 232 can be found in our media database:
The 232 has a setup assistant that guides you through the set-up process on the
device display.
Please read this operation manual in full and keep it in a safe place.
232 i n t e g r a t e d a m p l i f i e r
c l a s s i c l i n e
Connecting and starting up the 232
Important information
RISK OF INJURY!
The device is very heavy. Take care when unpacking and
setting it up!
RISK OF INJURY AND SUFFOCATION!
The device is not suitable for use by children.
Keep the packaging and small parts out of reach of children.
DANGER DUE TO ELECTRIC CURRENT!
Only operate the device on mains with a protective earth conductor.
Observe the mains voltage of your country. The externally
accessible mains fuse on the rear of the device must only be
replaced by authorised personnel. Do not open the device.
Do not touch the speaker’s binding posts when the device is
switched on.
INTENDED USE
The Burmester 232 is intended for use in home music systems.
PERMISSIBLE OPERATING CONDITIONS
Please take care to only ever use your Burmester product under the following
conditions:
Maximum altitude: 2000 m
Humidity < 50%
Temperature range: 20–30° C
CAUTION! HIGHINTENSITY SOUND
Loud output signals can damage your hearing. Avoid listening at high
volume levels for long periods of time.
Insert all connectors before switching on the 232.
1. Place the 232 on a flat, stable surface. Do not use the 232 outdoors.
2. Connect your analogue source devices to the analogue inputs (blue) of the 232.
Note: In order to play back digital sources, the optional digital module
must be installed. To play vinyl records (MC), the optional phono module
must be installed.
3. Connect your speaker to the speaker outputs (orange) on the 232 using
prefabricated loudspeaker cables with spade lugs. Observe the correct polarity
(plus to plus, minus to minus). Make sure that the connections are secure.
Note: The insulation on your selected speaker cable must match that of the original
Burmester loudspeaker cable and must have a flame rating of at least VW-1.
4. Set the mains switch on the rear of the device (green) to “OFF”. Connect the 232 to
the mains and set the mains switch to “ON”.
5. Switch the 232 on by pressing the rotary encoder (red).
6. Follow the instructions on the display to select the source.
7. Control the playback volume by turning the rotary encoder (red).
Quick start guide
232 i n t e g rat e d a m pl i f i e r
OPERATION MANUAL AND SAFETY INFORMATION
BA_232_short_en_1-1_2311
Burmester Home Audio GmbH
Wilhelm-Kabus-Straße 47
10829 Berlin

Summary

Connecting and Starting Up

Connecting Sources and Speakers

Connect analogue sources and speakers to the 232, observing polarity and cable requirements.

Power On and Initial Operation

Connect to mains, power on the device, and follow display prompts to select source and control playback.

Intended Use

Permissible Operating Conditions

Important Safety Information

Risk of Injury (Weight)

The device is heavy; handle with care during unpacking and setup to avoid injury.

Risk of Injury and Suffocation (Children)

Not suitable for children; keep packaging and small parts out of reach.

Danger of Electric Current

Use with protective earth conductor; observe voltage; authorized personnel for fuse replacement.

Caution: High-Intensity Sound

Loud output signals can damage hearing; avoid prolonged high volume listening.

Technical Specifications

Errors and Support

Disposal Information

Burmester 232 Specifications

General

Type	Integrated Amplifier
Total Harmonic Distortion (THD)	< 0.03%
Signal-to-Noise Ratio	> 100 dB
Inputs	XLR, RCA
Outputs	Speaker Outputs, Pre-Out
Special Features	Fully balanced circuitry, remote control