EasyManua.ls Logo

BUSCH PUMA WP 0250 D4 - User Manual

BUSCH PUMA WP 0250 D4
36 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Get technical data,
instruction manuals,
service kits
PUMA
Vacuum Boosters
WP 0250 D4, WP 0500 D2/D4, WP 0700 D2,
WP 1000 D2/D4, WP 1250 D2, WP 2000 D2
Instruction Manual
0870571055 | -0007_en-US | Original instructions 5/24/2022

Table of Contents

Questions and Answers

  • M
    Michele ScottAug 16, 2025
    Why does my BUSCH PUMA WP 0250 D4 Water Pump run too hot?
    • K
      kevinnealAug 16, 2025
      Your BUSCH Water Pump might be running too hot due to several reasons: * Insufficient cooling. For WP 1000 D4 and WP 2000 D2 versions, ensure compliance with cooling water requirements. * High ambient temperature. Make sure to observe the permitted ambient temperature. * High temperature of the process gases at the inlet. Ensure you observe the permitted gas inlet temperature. * Low oil level. Top up the oil. * Incorrectly defined backing pump. In this case, contact Busch for assistance.
  • M
    moyerbarbaraAug 19, 2025
    What to do if my BUSCH Water Pump does not start?
    • A
      Ashley KingSep 12, 2025
      If your BUSCH Water Pump doesn't start, it could be due to the following reasons: * The motor isn't getting the correct voltage. In this case, check the power supply. * The lobes are jammed or seized. You should consider lobes inspection or repair the machine (contact Busch). * Solid foreign matter has entered the machine. Remove the solid foreign matter or repair the machine (contact Busch). Equip the machine with a mesh screen at the suction connection. * The motor is defective. Replace the motor.
  • M
    Matthew AllenAug 22, 2025
    Why doesn't my BUSCH PUMA WP 0250 D4 reach the usual pressure?
    • L
      Lucas TurnerAug 22, 2025
      If your BUSCH Water Pump isn't reaching its usual pressure, consider these potential causes: * Suction or discharge lines are too long or the section diameter is too small. Use larger diameter or shorter lines. Seek advice from your local Busch representative. * The backing pump is not correctly defined. Contact Busch for assistance. * The machine is running in the wrong direction. Check the direction of rotation, see Wiring Diagram Three-Phase Motor. * Internal parts are worn or damaged. Repair the machine (contact Busch).
  • M
    Mary HarperAug 25, 2025
    Why does my BUSCH PUMA WP 0250 D4 run very noisily?
    • J
      Jay KimAug 26, 2025
      If your BUSCH Water Pump is running very noisily, it could be due to: * Wrong oil quantity or unsuitable oil type. Use one of the recommended oils in the correct quantity. * Defective gears, bearings, or coupling element. Repair the machine (contact Busch).
  • P
    Paul RoseAug 28, 2025
    Why is the oil in my BUSCH PUMA WP 0250 D4 Water Pump black?
    • M
      Mr. Samuel MooreAug 28, 2025
      The oil in your BUSCH Water Pump might be black because: * Oil change intervals are too long. Drain the oil and fill in new oil. * The machine runs too hot. Refer to the troubleshooting steps for "The machine runs too hot".
  • G
    Glenn HollandAug 31, 2025
    What to do if my BUSCH Industrial Equipment machine does not start?
    • D
      Dr. Douglas DavisAug 31, 2025
      If your BUSCH industrial equipment machine does not start, it could be due to several reasons. First, the motor might not be getting the right voltage, so check the power supply. Second, the lobes might be jammed; in this case lobes inspection or repair the machine (contact Busch). Third, solid matter might have entered the machine; remove it and consider equipping the machine with a mesh screen at the suction connection. Finally, the motor itself could be defective, requiring replacement.
  • J
    Joseph SmithSep 3, 2025
    Why is my BUSCH Industrial Equipment running too hot?
    • W
      wrightmichaelSep 3, 2025
      Your BUSCH industrial equipment might be running too hot due to several reasons. There might be insufficient cooling. For versions WP 1000 D4 and WP 2000 D2: Make sure to comply with the cooling water requirements. The ambient temperature or the temperature of process gases at the inlet could be too high; observe the permitted temperature. Also, the oil level might be too low, so top up the oil. The backing pump might not be correctly defined; in that case contact Busch.
  • M
    Miss Kathryn Stewart DVMSep 6, 2025
    What to do if my BUSCH Industrial Equipment does not reach the usual pressure?
    • E
      emilywhiteSep 6, 2025
      If your BUSCH industrial equipment isn't reaching its usual pressure, it could be due to several factors. The suction or discharge lines might be too long or have too small a diameter; try using larger diameter or shorter lines. The backing pump may not be correctly defined; in that case, contact Busch. The machine might be running in the wrong direction; check the direction of rotation. Also, internal parts may be worn or damaged; in that case repair the machine (contact Busch).
  • A
    Amanda RodriguezSep 9, 2025
    How to fix a BUSCH Industrial Equipment machine that runs very noisily?
    • S
      Susan RobertsSep 9, 2025
      If your BUSCH industrial equipment machine is running very noisily, it could be due to the wrong oil quantity or an unsuitable oil type; use one of the recommended oils in the correct quantity. Alternatively, there may be defective gears, bearings, or a coupling element; in that case, repair the machine (contact Busch).
  • B
    Brian PalmerSep 12, 2025
    Why is the oil in my BUSCH Industrial Equipment black?
    • C
      Cheryl DaySep 12, 2025
      The oil in your BUSCH industrial equipment might be black because the oil change intervals are too long; drain the old oil and fill in new oil. Another reason could be that the machine runs too hot; see the troubleshooting section addressing that issue.

BUSCH PUMA WP 0250 D4 Specifications

General IconGeneral
ModelPUMA WP 0250 D4
Voltage230 V
Frequency50 Hz
Inlet Diameter1 inch
Outlet Diameter1 inch
Power250 W
Protection ClassIPX4

Related product manuals