Bush Hog BH16 - User Manual

Questions and Answers

D
Dr. David TurnerAug 15, 2025
Why is my Bush Hog BH16 leaving an uneven cut?
- J
  jacquelinestephensonAug 16, 2025
  An uneven cut from your Bush Hog Lawn Mower can stem from several factors. You might be operating at excessive ground speed, which requires you to reduce your speed. The blades could be worn, dull, or bent, indicating they need replacement. The mower might not be level, necessitating an adjustment. Check if the mower height is improperly adjusted; if so, adjust it accordingly. Uneven tire pressure on the tractor, damaged mower pan, or turning too fast can also cause this issue. Adjust tire pressure, repair or replace the mower pan, or reduce ground speed when turning. Finally, tractor tires may be pushing the grass down; adjust your tractor wheel spacing.
P
Patty JohnsonAug 18, 2025
Why is my Bush Hog BH16 Lawn Mower not cutting material?
- M
  Mitchell BonillaAug 18, 2025
  If your Bush Hog Lawn Mower is not cutting material, it could be due to excessive ground speed, so reduce it. Ensure you are using full PTO speed. Also, check that the blades are installed correctly for the direction of cut.
J
Jennifer SchmidtAug 21, 2025
What causes streaking conditions with my Bush Hog BH16 Lawn Mower?
- J
  Jennifer LucasAug 21, 2025
  Streaking while using your Bush Hog Lawn Mower can occur if conditions are too wet, so allow the grass to dry before cutting. It may also happen if the blades are dull, so sharpen or replace them. Another cause can be the height of the cutter being lower at the rear or front, or if the blades are too slow relative to the tractor's ground speed. Lowering the cutting height may help.
P
patriciaortizAug 25, 2025
Why is my Bush Hog BH16 not shredding properly?
- M
  Matthew NielsenAug 25, 2025
  Poor shredding with your Bush Hog Lawn Mower can result from excessive ground speed. Try raising the front of the mower relative to the rear to hold and circulate material longer, and reduce ground speed. Also, if you are cutting too high, lower the cutting height.
T
Tyler MartinezAug 27, 2025
What to do if my Bush Hog BH16 Lawn Mower gearbox is leaking?
- M
  Michael SanchezAug 27, 2025
  If your Bush Hog Lawn Mower gearbox is leaking, there are several potential causes. The oil seal might be damaged, installed incorrectly, or not sealing properly in the housing, requiring replacement or the use of a sealant. A bent shaft or a rough oil seal race also necessitates replacement or repair. Other possible causes include a damaged gasket, loose bolts, a sand hole in the casting, or an oil level that is too high. Replace the gasket, tighten the bolts, replace the castings or gearbox, or drain the oil to the proper level.
R
Rebecca BowmanAug 30, 2025
Why does my Bush Hog BH16 keep shearing pins?
- J
  Jamie CastilloAug 30, 2025
  Shear pin shearing in your Bush Hog Lawn Mower can occur due to several reasons: * The tractor PTO might not be running at 540 RPM – ensure it is. * You may be dealing with heavy material – reduce ground speed. * An incorrect shear pin may be in use – replace it with the recommended one. * The PTO might be engaged at high engine RPM – idle the engine before engaging. * Rocky conditions may be present – increase cutting height. * The blade carrier RPM might be too high – check gearbox ratios.
J
jennifer34Sep 2, 2025
Why is my Bush Hog Lawn Mower gearbox noisy?
- K
  Kelly HendersonSep 2, 2025
  A noisy gearbox in your Bush Hog Lawn Mower can be attributed to a few reasons. The lubricant level might be low, so check and replenish it. The gears could be rough, requiring a run-in or change. Alternatively, a worn bearing might be the cause, which would need replacement.
M
Mr. Shawn GeorgeSep 5, 2025
Why is my Bush Hog Lawn Mower windrowing?
- V
  Vanessa PaulSep 5, 2025
  Windrowing with your Bush Hog Lawn Mower can occur if the material is heavy and lush. In this case, try raising the front of the mower relative to the rear. Excessive ground speed can also cause windrowing, so reduce your speed. Wet conditions may also contribute, so wait for the conditions to dry.
F
fmeltonSep 8, 2025
Why are the blade bolts on my Bush Hog Lawn Mower working loose?
- J
  Jonathan JonesSep 8, 2025
  If the blade bolts on your Bush Hog Lawn Mower are working loose, it could be because they weren't tightened sufficiently; tighten the bolts to 600 ft./lbs. Alternatively, the bolt hole may be elongated or oversized, requiring replacement of the blade carrier. A broken lockwasher can also cause this issue, so replace the lockwasher.
J
Jason DunnSep 12, 2025
Why is my Bush Hog BH16 gearbox overheating?
- R
  ramseyalexandraSep 12, 2025
  Gearbox overheating in your Bush Hog Lawn Mower can be due to low lubricant, so fill it to the level plug. It may also happen if the lubricant type is incorrect, so replace it with the proper lubricant. Excessive trash build-up around the gearbox can also cause overheating, so remove any trash.