Residual heat ındicator
The residual heat indicator indicates that the glass ceramic
area has a temperature that is dangerous to touch.
After switching off the cooking zone, the respective display
will show “H” until the corresponding cooking zone
temperature is at a safe level.
Smart pause
Smart Pause, when activated, reduces the power of all
burners that have been switched on.
If you then deactivate the Smart Pause, the heaters will
automatically return to the previous temperature level.
If the Smart Pause is not de-activated, the cooktop will switch
off after 30 minutes.
Press
to activate Smart Pause. The power for the
activated heater(s) will reduce to level 1 and “II” will appear at
all displays.
Press
again to deactivate Smart Pause. “II” will disappear
and the heaters will now run at the level previously set.
Safety switch-off function
A cooking zone will automatically switch off if the heat
setting has not been modified for a specified duration of time.
A change in the heat setting of the cooking zone will reset
the time duration to the initial value. This initial value depends
on the selected temperature level, as shown below.
Heat setting Safety switch off after
1-2 6 Hours
3-4 5 Hours
5 4 Hours
6-9 1.5 Hours
Child lock
After switching on the appliance, the child lock function can
be activated. To activate the child lock, simultaneously press
the increase heat setting button
and decrease heat setting
button and then press the increase heat setting key
again. “L” indicating LOCKED will appear on all heater displays
and the controls can not be used. (If a cooking zone is in the
hot condition, “L” and “H” will display alternately).
The hob will remain in a locked condition until it is unlocked,
even if the appliance has been switched off and on.
To deactivate the child lock, first switch on the hob.
Simultaneously press the increase heat setting button
and
decrease heat setting button and then press the decrease
heat setting button again. “L” will no longer be displayed
and the hob will switch off.
Key lock
The key lock function is used to set ‘safe mode’ on the
appliance during operation. It will not be possible to make
any adjustments by pressing the buttons (for example heat
settings). It will only be possible to switch the appliance off.
The lock function is active if the key lock button
is pressed
for at least 2 seconds. This operation is acknowledged by a
buzzer. After successful operation, the key lock indicator will
flash and the heater will be locked.
Buzzer
While the hob is in operation, the following activities will be
signalled by the buzzer.
• Normal button activation will be accompanied with a
short sound signal.
• Continuous button operation over a longer period of
time (10 seconds) will be accompanied with a longer,
intermittent sound signal.
Boost function
To use this function, select a cooking zone and set the
desired cooking level, then press the “P” (Boost) button.
The Boost function can only be activated if it is applicable
with the cooking zone selected. If the Boost Function is
active, a “P” is shown on the corresponding display.
Activating the booster can exceed the maximum power,
in which case the integrated power management will be
activated.
The necessary power reduction is shown by the
corresponding cooking zone display blinking. Blinking will be
active for 3 seconds to allow for further adaptations of the
settings before power reduction.
Error Codes
If there is an error, an error code will be shown on the
heater displays.
E1 Cooling Fan is disabled. Call an authorised
service agent.
E3 Supply voltage is other than the rated values.
Switch the hob off by pressing
,wait until “H”
disappears for all zones, switch the hob on by
pressing and continue to use. If the same
error is displayed again, call an authorised
service agent.
E4 Supply frequency is different from the rated
values. Switch the hob off by pressing
, wait
until “H” disappears from all zones, switch the
hob on by pressing and continue to use. If
the same error is displayed again, switch the
plug for the appliance off and on. Switch the
hob on by pressing and continue to use.
If the same error is displayed again, call an
authorised service agent.
E5 Internal temperature of the hob is too high,
switch the hob off by pressing
and let the
heaters cool down.
E6 Communication error between the touch
control and heater. Call an authorised service
agent.
E7 Coil temperature sensor is disabled. Call an
authorized service agent.
E8 Cooler temperature sensor is disabled. Call an
authorized service agent.
E9 Calibration error. Call authorised service agent.
To Next Page
Loading...
