Buyers Products Company LT35 User Manual

Quality since 1946
9049 Tyler Blvd. • Mentor, Ohio 44060
Phone (440) 974-8888 • Fax (440) 974-0165
Toll-Free Fax 800-841-8003 • buyersproducts.com
Installation Instructions
LT35 Hand Tool Rack
for Utility Landscape Trailers
—continued on other side
1 3004207 1 Post, Hand Tool Rack
2 3004165 2 Angle, Tool Holder
3 3004167 12 Grommet, Rubber, for 2" hole
4 - 4 Screw, HHC 5/16-18 x 1-1/2 Gr 5 Zn
5 - 4 Nut, Nylock 5/16-18 Zn
6 - 6 Washer, Flat 3/8 USS Zn
7 - 1 Screw, HHC 3/8-16 x 2 Gr 5 Zp
8 - 2 Screw, HHC 3/8-16 x 2-1/2 Gr 5 Zp
9 - 3 Nut, Nylock 3/8-16 x 7/16 Zn
10 - 1 Plug, Plastic Finish, 1" Square Tube
ITEM PART NO. QTY. DESCRIPTION
Bill of Materials
Important!
Before you begin installing:
1. Read and understand these instructions
completely.
2. Verify that you have received all the parts
listed in the bill of materials.
Tools Required:
•Two 9/16" wrenches and/or sockets
•Two 1/2" wrenches and/or sockets
•Electric drill
•13/32” Drill bit
•Carpenter’s square
•C-clamp
CAUTION:
Always wear safety glasses when using power tools.
1. Clamp the post of the hand tool rack to the
trailer side rail. The hand tool rack uses 4" x 23"
of the trailer floor space and the post is centered
in this space. Position the hand tool rack such
that the lawn mowers or other equipment will
not damage the hand tool handles. Verify that
the post is square to the trailer deck in both direc-
tions with a carpenter’s square.
2. After determining the position of the post
mark center of the two holes in each upright base
on the trailer deck.
WARNING! Check under the trailer for locations
of brake lines and electrical wiring etc., before
drilling any holes. Any damage to trailer during
installation is installer’s full responsibility.
3. Remove the post from the trailer and use a
13/32" drill bit to drill two holes in your trailer
floor as marked.

Buyers Products Company LT35 Specifications

General

Wattage	35W
Housing Material	Aluminum
Lens Material	Polycarbonate
IP Rating	IP67
Color	Black
Voltage	12-24 VDC
Material	Aluminum

Summary

Installation Instructions

Clamp Post to Trailer Side Rail

Clamp the hand tool rack post to the trailer side rail, ensuring it is square to the deck in both directions.

Mark Mounting Holes on Trailer Deck

After positioning, mark the center of the two holes in each upright base on the trailer deck for drilling.

Drill Mounting Holes in Trailer Floor

Remove the post from the trailer and drill two holes in the trailer floor using a 13/32" drill bit.

Attach Post to Trailer Base

Assemble the post to the trailer using 3/8" cap screws, washers, and nylock nuts, but do not tighten fully yet.

Square Post to Rail and Deck

Clamp the post to the trailer rail and ensure it is square to both the rail and the deck using a square.

Drill Post and Rail for Fastening

With the post clamped, drill a 13/32" hole through the center of the post and the trailer rail.

Secure Post to Trailer Rail

Fasten the post to the trailer rail using a 3/8" cap screw, two 3/8" flat washers, and a 3/8" nylock nut.

Assemble Tool Holder Brackets

Attach the tool holder angle brackets to the post using four 5/16" cap screws and nylock nuts.

Install Grommets in Tool Holders

Assemble the twelve rubber grommets into the two inch holes in the tool holder angles.