CAB a3-2 Service Manual

I-3
Serviceanleitung / Service Manual / / /
R
Reinigung, allgemein ............................................... 35
Reinigung der Druckwalze ....................................... 36
Reinigung der Etikettenlichtschranke....................... 36
Reinigung des Druckkopfes..................................... 35
Riemenspannung .................................................... 78
Rücksetzen der Servicezähler ........................... 19, 30
Rutschkupplungen, Wechsel ................................... 46
S
Schnittstellen .................................... 13, 16, 19, 25, 26
Schriften .................................................................. 16
Schriftenliste ...................................................... 17, 23
Serviceschlüssel...................................................... 19
Servicezähler zurücksetzen ............................... 19, 30
Sicherheit beim Umgang mit Elektrizität .................... 7
Sicherheitshinweise ................................................... 6
Spendekante ............................................... 10, 12, 25
Statusausdruck............................................ 17, 24, 31
Statusmeldungen......................................... 16, 17, 21
T
Technische Daten ................................................... 14
Teile des Etikettendruckers ..................................... 11
Testfunktionen......................................................... 23
Testgitter ................................................................. 23
Thermodruckkopf ......................... 9, 12, 14, 24, 35, 40
Transferfolienabwickler................................ 11, 46, 66
Transferfolienaufwickler .............................. 11, 46, 66
Transferfolienumlenkblech .......................... 12, 72, 80
U
Überwachung/Test ............................................ 17, 23
Uhrzeit ..............................................15, 25, 28, 29, 30
Umgebungsbedingungen......................................... 17
Umlenkblech............................................................ 13
Umlenkwalze ........................................................... 12
Umlenkwalze, Wechsel ........................................... 44
USB-Schnittstelle.................. 13, 16, 19, 26, C-8, C-16
V
Verpackung ............................................................. 10
W
Wartung................................................................... 35
Wechsel der Druckwalze und der Umlenkwalze ...... 44
Wechsel der Etikettenlichtschranke......................... 49
Wechsel der Leiterplatte CPU ................................. 51
Wechsel der Rutschkupplungen .............................. 46
Wechsel des Druckkopfes....................................... 40
Wechsel des Netzteils ............................................. 54
Wechsel von Baugruppen ....................................... 39
Werkzeuge .............................................................. 39
Wickelmomente....................................................... 66
Z
Zeichensatz ................................................. 16, 22, 25
R
Replacing assembly units ........................................ 39
Replacing the label edge sensor.............................. 49
Replacing the PCB CPU .......................................... 51
Replacing the power unit ......................................... 54
Replacing the printhead ........................................... 40
Replacing the print roller .......................................... 44
Replacing the rewind assist roller ............................ 44
Replacing the slipping clutches................................ 46
Rewind assist roller ................................................. 12
Rewind assist roller, replacing ................................. 44
Rewind guide plate .................................................. 13
Ribbon shield ............................................... 12, 72, 80
Ribbon supply hub ....................................... 11, 46, 66
Ribbon take up hub ..................................... 11, 46, 66
S
Safe handling of electricity ......................................... 7
Safety instructions ..................................................... 6
Save NVRAM .......................................................... 33
Service counter, reset........................................ 19, 30
Service key .............................................................. 19
Short status ................................................. 17, 23, 30
Slipping clutches, replacing ..................................... 46
Spare parts ................................................ Appendix A
Status messages ......................................... 16, 17, 21
Status print .................................................. 17, 24, 31
T
Tear-off plate ........................................................... 13
Technical specifications........................................... 14
Test functions .......................................................... 23
Test grid .................................................................. 23
Thermal Printhead ........................ 9, 12, 14, 24, 35, 40
Time ................................................. 15, 25, 28, 29, 30
Tools ....................................................................... 39
Trouble Diagnosis.............................................. 17, 80
U
Updating the firmware ......................24, 28, 30, 53, 59
USB interface ....................... 13, 16, 19, 26, C-8, C-16

CAB a3-2 Specifications

General

Brand	CAB
Model	a3-2
Category	Printer
Language	English