What to do if the liquid level meter does not work on CAIRE Liberator G4?
If the liquid level meter on your CAIRE Oxygen Equipment does not work or is not accurate, the battery may need to be replaced or the meter re-calibrated. Contact your service provider for assistance.
Why is my CAIRE Medical Equipment venting excessively from relief valves (hissing sound)?
Excessive venting, indicated by a hissing sound, could be due to several reasons. The saturation pressure might be too high, so inspect it and allow at least 30 minutes at no flow for proper saturation. The relief valve might be frozen open, in which case you should allow the portable unit to warm and thaw before attempting to refill it. A faulty relief valve could also be the cause, requiring a test and possible replacement. Finally, a partial or complete loss of vacuum may be the issue, requiring a NER test and possible return of the unit.
What to do if my CAIRE Medical Equipment has low flow at the oxygen outlet on all LPM settings?
If you're experiencing low flow at the oxygen outlet on all LPM settings, start by inspecting the nasal cannula for kinks or leaks. Check the saturation pressure of the reservoir, allowing at least 30 minutes at no flow for proper saturation. Perform a leak check on the plumbing and repair any leaks. Clean or replace the flow control valve inlet filter screen if it's dirty. Test the economizer valve and replace it if necessary. Check the warming coils and withdrawal tubes, as well as the flow restrictor, for blockages and replace if needed. Finally, the FCV might be faulty and require replacement.
How to troubleshoot increased NER in CAIRE Medical Equipment?
To troubleshoot increased NER, first inspect the saturation pressure of the reservoir, ensuring it has had at least 30 minutes at no flow to saturate properly. Next, perform a leak check on the plumbing and repair any leaks. Ensure that there is no venting from the relief valves; if there is, refer to the corrective actions for excessive venting. Finally, check for a partial or complete loss of vacuum by conducting the NER test and returning the unit to CAIRE, Inc., if necessary.
Why is my CAIRE Medical Equipment unable to start fill or has excessively long fill times?
If your CAIRE Medical Equipment is unable to start filling or has excessively long fill times, it could be due to several reasons. Make sure the transfer line is fully engaged on the Reservoir QDV and properly aligned, applying downward force. Verify that the source pressure is within the 35-50 psi range. Ensure the vent valve is fully open and not blocked. The source tank might be under or over-saturated, so allow LOX to saturate to proper pressure. Check the fill connector and cartridge assembly for damage, ensuring full engagement. Inspect the vent valve for blockages and clean with compressed gas if necessary. Finally, check the reservoir for leaks and repair if needed.
What does it mean when the low battery LED is illuminated on the liquid level meter of my CAIRE Liberator G4?
If the low battery LED is illuminated on the liquid level meter of your CAIRE Oxygen Equipment, contact your service provider for assistance.
What to do if liquid oxygen evacuates from the blue QDV on my CAIRE Liberator G4?
If liquid oxygen is evacuating from the blue QDV of your CAIRE Oxygen Equipment, the QDV may have frozen open. Open windows if possible and evacuate the area immediately. To prevent this, wipe the QDV with a dry, lint-free cloth before and after filling your portable.
Why is there frosting on the tank or side of my CAIRE Liberator Oxygen Equipment?
If there is frosting on the tank or side of your CAIRE Liberator, this is abnormal; contact your service provider for assistance.
What to do if there is condensation or water pooling up on the floor from my CAIRE Liberator G4 Oxygen Equipment?
If you notice condensation or water pooling on the floor near your CAIRE Oxygen Equipment, this may happen because water accumulates when frost melts on the coils. Ensure that the condensate bottle is installed correctly and emptied as needed; it may be full or not properly in place.
How to fix liquid leaks from coupled QDVs during fill of CAIRE Medical Equipment?
If liquid leaks from the coupled QDVs during the fill, the most likely cause is a worn or damaged lip seal. Replace the QDV lip seal.
General| Brand | CAIRE |
|---|---|
| Model | Liberator G4 Series |
| Category | Oxygen Equipment |
| Language | English |
To Next Page
