Need help?Do you have a question about the Cal Spas SWIM PRO SPAS and is the answer not in the manual?
Warnings about drowning, injury from usage, and electrical hazards like shock or electrocution.
Details risks of high water temperatures, prolonged exposure, and specific health considerations.
Explains GFCI testing procedures and reiterates electrical safety warnings.
Covers warnings for specific health conditions, exercise, and general usage.
Essential steps before delivery and guidance on choosing the best spa location.
Ensuring clear access for service and preparing a solid, level foundation.
Details acceptable wiring procedures and compliance requirements for 240V spas.
Outlines required GFCI types and wire gauges based on spa model and distance.
Provides a visual guide for connecting the circuit board in North American configurations.
Illustrates the electrical wiring setup for European spas with 50Hz frequency.
Depicts the wiring diagram for US and Canadian installations using Balboa systems.
Shows the wiring diagram for European installations using Balboa systems.
Steps to inspect equipment and remove the filter cartridge before filling.
Instructions on how to fill the spa with water to the correct level, avoiding soft water.
Guide to turn on the spa's power supply after filling and filter installation.
Explains the priming mode for the pump and how the system exits it.
Describes the initial start-up sequence and the priming mode display on the control panel.
Provides manual steps to bleed air from the pump if it fails to prime.
Details the main screen, priming mode, and basic spa operation functions.
Explains how to navigate menus and adjust the spa's water set temperature.
Explains control panel icons and the timeout feature for energy saving.
Provides steps to access and navigate various setting screens on the control panel.
Details various settings like Rotate View, Special Temp, Heat Mode, and Filter Cycles.
Explains how to lock/unlock the panel and access service modes.
Describes error messages related to plumbing, flow, overheat, and freeze conditions.
Details error messages for sensor faults and communication issues.
Guidance on adjusting settings for cold weather, including energy interval and heat mode.
Introduces the spaTouch icon-driven control panel interface.
Provides a step-by-step guide on how to change the display language on the spaTouch panel.
Explains the meaning and function of various icons displayed on the spa control screen.
Describes how to navigate the spa's menu structure and access waiting messages.
Details how to set the spa temperature and access control for spa equipment.
Describes how to adjust values and use the invert display feature.
Explains how to exit screens and save or cancel changes made to settings.
Describes how to move between different pages or lists using navigation arrows.
Details how to set the heat mode and configure dual temperature ranges (High vs. Low).
Explains the differences between Ready, Rest, and Ready-in-Rest modes for spa heating.
Explains freeze protection and the operation of filtration and ozone systems.
Guides on how to set the correct time-of-day for proper operation of scheduled features.
Instructions for setting the start time, end time, and duration for the primary filter cycle.
Guide on enabling and configuring a second filter cycle and the LED lighting timer.
Step-by-step instructions on how to lock the spa control panel for security.
Details the Hold Mode for service and the optional Drain Mode for water removal.
Guides on setting the sleep timer and explains the Demo Mode and Fault Log.
Covers how to change temperature units and select display languages.
Explains messages related to unknown water temperature, freezing conditions, and hot water alerts.
Details error messages for water flow issues, dry heater, and heater overheating.
Lists common causes and checks for heater-related flow issues.
Explains error messages for sensor synchronization issues and sensor failures.
Covers errors like program memory failure, GFCI test failures, and communications errors.
Details messages concerning program memory, settings reset, clock, GFCI, and pump status.
Details various reminder messages for maintenance tasks and their configuration.
Introduces the spaTouch 3 user guide and its table of contents.
Details the icons indicating spa status and functioning buttons on the main screen.
Explains how to interpret icons on the main screen for temperature, messages, and lock status.
Instructions on how to wake the spa control panel from sleep mode.
Identifies and explains the functions of various buttons and the temperature display.
Explains how the Mini Player button accesses temperature/time and music controls.
Describes the function of the bba™ button and how to navigate screens and lists.
Explains how to exit screens and save or cancel changes made to settings.
Explains how to view, dismiss, or exit messages displayed on the spa panel.
Step-by-step guide on how to set the spa's time-of-day using the control panel.
Detailed steps on how to change the spa's set temperature using the control panel interface.
Explains how to determine if the spa's heater is active based on the control panel icon.
Instructions for setting the start time, end time, and duration for the primary filter cycle.
Guide on enabling and configuring a second filter cycle and the LED lighting timer.
Explains different modes for circulation pumps and their programmability.
Details the purpose and function of purge cycles and the meaning of filter cycles.
Step-by-step instructions on how to lock the spa control panel for security.
Detailed steps to lock the spa panel, preventing unauthorized access or changes.
Step-by-step instructions on how to unlock the spa control panel.
Describes how to lock both the panel and settings concurrently and interpret lock states.
Details how pumps operate, including time-out periods and circulation pump functions.
Explains how alternative pumps function in systems without a dedicated circulation pump.
Explains the three different configurations for circulation pump operation.
Explains how filtration cycles and ozone generators work, including programming.
Instructions on how to access and use the diagnostics screen for system information.
Details what information is available in the 'Info' and 'Faults' sections of the diagnostics screen.
Explains the three ways GFCI can be configured and the automatic test function.
Discusses the GFCI Test feature for verifying correct installation and safety.
Step-by-step guide for manually testing the GFCI using the control panel.
Explains how to interpret test results and when to contact a service technician.
Explains the differences between Ready, Rest, and Ready-in-Rest modes for spa heating.
Explains how to set and switch between High and Low temperature ranges for the spa.
Describes the M8 feature for reducing pump usage and saving energy.
Guides on accessing settings and basic options like Heat, Filter, and Time.
Explains settings for maintenance reminders, panel/setting locks, and light control.
Details the Hold Mode for service and the optional Drain Mode for water removal.
Covers the Cleanup Cycle setting, units preference, and language selection.
Instructions for preparing the spa and filling it with water, opening valves and jets.
Explains the priming mode, its purpose, and how pumps are energized.
Describes general alerts like freezing conditions and hot water warnings.
Details error messages related to water flow, heater status, and temperature.
Explains error messages for sensor synchronization issues and sensor failures.
Covers errors like program memory failure, GFCI test failures, and communications errors.
Details various reminder messages for maintenance tasks and their configuration.
Covers communications errors and test software messages requiring service attention.
Guide for connecting your device directly to the spa's Wi-Fi module.
Instructions for connecting the spa through your home network, with or without internet access.
Steps to download and install the Cal Spas Wi-Fi app from app stores.
Guide on enabling Wi-Fi and connecting to the spa via the app for remote control.
Tips for resolving issues when connecting to the spa's Wi-Fi or app.
Explains how to use the ATS pump, pulse modes, and segment display.
Describes the ATS sensor's role in temperature monitoring and pump protection.
Provides advice for ensuring efficient operation of the spa's electric heater.
Explains how to adjust jets and control the spa's LED lighting modes.
Explains how to use diverter knobs and air venturi valves to control water and air flow.
Instructions for operating optional waterfalls, including adjustment and shutdown.
Outlines the four main factors contributing to excellent spa water quality: balance, sanitation, filtration, and regularity.
Introduces reagent test kits and test strips for monitoring spa water chemistry.
Explains how to balance total alkalinity, pH, and calcium hardness for proper water chemistry.
Recommends chlorine or bromine as sanitizers and provides usage guidance.
Explains the process and benefits of shocking the spa water to remove contaminants.
Discusses bather load effects and filter cleaning procedures for water clarity.
Explains the ozonator and factory-programmed filter cycles.
Covers water sanitation, programmed filter cycles, and adjustments for bather load.
Provides a schedule for regular spa maintenance tasks like refilling, testing, and cleaning.
Lists probable causes and solutions for cloudy spa water and water odor issues.
Step-by-step guide for removing, cleaning, and re-installing spa pillows and jets.
Process for cleaning hydrostreamer jets to ensure proper water flow.
Detailed steps for disassembling and cleaning hydrostreamer jets.
Guide on how to install the spa cover's locking hardware for security.
Instructions for securing the spa cover using the provided hardware and key.
Steps to locate the spa drain, remove the cap, and connect a garden hose.
Procedure for draining the spa water and replacing the drain cap.
Detailed steps for draining and preparing the spa for cold weather to prevent freeze damage.
Explains the importance of filter cleaning and replacement for water clarity and spa function.
Guidance on preparing the spa for periods of inactivity, including cover locking and water treatment.
Advises on draining or winterizing the spa for extended periods of non-use.
Instructions for cleaning the spa cover, pillows, and shell with appropriate cleaners.
Guide on pairing a Bluetooth device with the spa's sound system for audio playback.
Explains how to use the control panel buttons and air venturi valves for the air injection system.
Instructions for assembling and using the swim tether pole for exercise.
Important safety advice and connection methods for the spa's exercise equipment.
Lists the contents of exercise kits for different spa sizes and how to connect them.
Shows various screw-in jet inserts with part numbers and dimensions.
Lists different types of jet inserts, pillows, and water diverter valves with part numbers.
Displays flush mount waterfall assemblies and air control valves.
Identifies different types of spa drains, teleweir skimmers, and filter cartridges.
Lists replacement LED light strings and associated components.
Details exercise kits and attachment plates for swim spa workouts.
Information on ordering replacement cabinet panels, spa covers, and lock systems.
Addresses issues like pumps not priming or breakers shutting off, with possible solutions.
Covers unresponsive control panels, operation issues, and spa water not getting hot.
Discusses causes and solutions for spa overheating, including ventilation and pump running times.
Addresses low/no water pressure and pump issues like constant running or noise.
Addresses pump faults like turning off during operation or having a burning smell.
Explains Thermal Creep and methods to manage it, such as venting the cover.
Outlines warranty periods for shell, equipment, controls, plumbing, and cabinets.
Details warranty coverage for various components like headrests, filters, and stereo systems.
States warranty is void if non-genuine parts are used, emphasizing quality of branded parts.
Explains warranty start date, service procedures, and owner's responsibility for access and freight.
Lists conditions that void the warranty, including misuse, neglect, and aftermarket parts.
Clarifies consumer legal rights and limitations on implied warranties.
Describes the manufacturer's right to repair or replace the spa, and associated costs.
Details specific exclusions and limitations on warranty coverage, including commercial use.
General| Manufacturer | Cal Spas |
|---|---|
| Category | Hot Tub |
| Seating Capacity | Varies by model |
| Number of Jets | Varies by model |
| Water Capacity | Varies by model |
| Dimensions | Varies by model |
| Heater | Varies by model |
| Pump | Varies by model |
| Filtration | Varies by model |
| Shell Material | Varies by model |
| Frame Material | Varies by model |
| Insulation | Varies by model |
| Control System | Varies by model |
| Lighting | Varies by model |
| Warranty | Varies by model |
To Next Page