CALEFFI SATK30103HE - User Manual

Questions and Answers

S
Sarah JohnsonAug 22, 2025
What to do if hot water flow rate is insufficient in CALEFFI SATK30103HE Recording Equipment?
- M
  Manuel WolfeAug 23, 2025
  If the hot water flow rate is insufficient, check if: * The domestic water system shut-off valves are partially or completely closed; if so, open the valves. * For other potential causes such as a clogged HIU strainer, insufficient centralised domestic circuit cold water flow rate, no cold water in centralised domestic circuit, or a completely clogged HIU strainer, it is recommended to call qualified personnel to have it serviced.
C
ccarterAug 27, 2025
Why is the hot water temperature too high in my CALEFFI Recording Equipment?
- K
  kristenwestAug 27, 2025
  If the hot water temperature is too high, consider the following: * Decrease the domestic water cycle temperature set point. * Restore the correct connection if the DHW temperature probe cable is inverted with the heating probe. * For other potential causes such as a faulty modulating valve actuator, a valve obturator blocked in intermediate or open position, a non-working electronic controller, or excessive pressure in the primary circuit, it is recommended to call qualified personnel to have it replaced or serviced. If there is excessive pressure in the primary circuit, contact the person in charge of the system.
J
Jason Harrington MDSep 1, 2025
What to do if CALEFFI SATK30103HE start-up triggers the safety circuit breaker?
- E
  Eric CarsonSep 1, 2025
  If the start-up of the heat interface unit heating function triggers the safety circuit breaker, check that the pump cable connector is inserted the right way round.
S
Shelly BanksNov 6, 2025
How to fix CALEFFI SATK30103HE when water is not heated?
- D
  danielle25Nov 6, 2025
  If the water is not heated, check the following: * Ensure the primary circuit shut-off valves are open. * Reconnect the modulating valve actuator connector if it's disconnected. * Reconnect the modulating valve actuator if it's disconnected from the valve body. * Restore the correct connection if the DHW temperature probe cable is inverted with the heating probe. * Vent the system to remove any air. * Reconnect the DHW temperature probe if disconnected. * Restore the correct switch setting if it's incorrect. * Reconnect the DHW priority flow meter if disconnected. * Restore the HIU electric supply if there is no electric power. * For other potential causes such as a faulty modulating valve actuator, a non-working electronic controller, a blocked valve obturator, a faul...
P
Paul YoungNov 11, 2025
What to do if CALEFFI SATK30103HE room is not reaching desired temperature?
- J
  Julie NavarroNov 11, 2025
  If the room is not reaching the desired temperature, consider the following: * Increase the heating cycle temperature set point. * Check the programming of the chrono-thermostat for incorrect temperature or time settings. * Reconnect the modulating valve actuator connector if disconnected. * Restore the correct connection if the DHW temperature probe cable is inverted with the heating probe. * Vent the system to remove any air. * Restore the pump cable connection if it's not connected. * Open any closed system shut-off valves/terminals. * Restore HIU electric supply if there is no electric power. * Restore system pressure if the heating circuit pressure is too low. * Restore correct switch setting if it's incorrect. * For other potential causes such as a clogged HIU ...
M
Matthew WolfNov 16, 2025
Why CALEFFI SATK30103HE water is hot but not reaching desired temperature?
- D
  Danny GrahamNov 16, 2025
  If the water is hot but not reaching the desired temperature, consider these potential causes: * Increase the domestic water cycle temperature set point. * Reconnect the modulating valve actuator connector if it is disconnected. * Restore the correct connection if the DHW temperature probe cable is inverted with the heating probe. * Decrease the demand if there is excessive demand for DHW. * For other potential causes such as a clogged primary circuit strainer of the HIU, a partly clogged heat exchanger, a faulty modulating valve actuator, a valve obturator blocked in intermediate position, a non-working electronic controller, insufficient centralised system temperature, or insufficient primary circuit flow rate, it is recommended to call qualified personnel to have it serviced ...