Campbell Hausfeld CHN20103 - User Manual

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or
property damage! Retain instructions for future reference.
See Warranty on page 8 for important information about commercial use of this product.
Operating Instructions CHN20103
REMINDER: Keep your dated proof of purchase for warranty purposes!
Attach it to this manual or file it for safekeeping.
IN732500AV 1/10
© 2010 Campbell Hausfeld/Scott Fetzer
Campbell Hausfeld Nailers meet or exceed Industries’ Standards as set forth by the American
National Standard Institute/International Staple, Nail and Tool Association in ANSI/ISANTA
SNT-101-2002.
For parts, product & service information
visit www.chpower.com
Table of Contents
Description . . . . . . . . . . . . . . . . . . . . . 1
Unpacking . . . . . . . . . . . . . . . . . . . . . . 1
Safety Guidelines . . . . . . . . . . . . . . . . 1
Important Safety Information . . . . . . 1
Tool Components and
Specifications. . . . . . . . . . . . . . . . . . . . 2
Operating Instructions . . . . . . . . . . . . 4
Lubrication . . . . . . . . . . . . . . . . . . . . 4
Recommended Hookup. . . . . . . . . . 4
Operational Mode . . . . . . . . . . . . . . 5
Work Contact Element (WCE). . . . . 5
Loading/Unloading The Tool. . . . . . 5
Adjusting the Nail Penetration. . . . 5
Adjusting the Direction
of the Exhaust . . . . . . . . . . . . . . . . . 5
User-Maintenance Instructions . . . . . 6
Clearing A Jam From The Tool . . . . 6
Technical Service . . . . . . . . . . . . . . . 6
Fastener And Replacement Parts . . 6
Tool Repair . . . . . . . . . . . . . . . . . . . . 6
Assembly Procedure For Seals. . . . . 6
Fastener Interchange Information. . . 6
Troubleshooting Chart . . . . . . . . . . . . 7
Warranty . . . . . . . . . . . . . . . . . . . . . . . 8
Description
This nailer is designed for decorative
trim, molding, window casings,
furniture trim and picture frame
assembly. Features include: convenient
rear loading magazine which holds
up to 100 nails, no-mar tip, adjustable
exhaust, single cycle trigger, quick clear
nose, and an adjustable depth of drive
mechanism.
Unpacking
After unpacking the unit, inspect
carefully for any damage that may
have occurred during transit. Make sure
to tighten fittings, bolts, etc., before
putting unit into service.
Safety Guidelines
This manual contains information
that is very important to know and
understand. This information is
provided for SAFETY and to PREVENT
EQUIPMENT PROBLEMS. To help
recognize this information, observe the
following symbols.
Danger indicates
an imminently
hazardous situation which, if not
avoided, WILL result in death or serious
injury.
Warning indicates
a potentially
hazardous situation which, if not
avoided, COULD result in death or
serious injury.
Caution indicates
a potentially
hazardous situation which, if not
avoided, MAY result in minor or
moderate injury.
Notice indicates
important
information, that if not followed, may
cause damage to equipment.
NOTE: Information that requires special
attention.
Important Safety Instructions
INSTRUCTIONS PERTAINING TO A
RISK OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS
Model CHN20103
Locate model and date code on
tool and record below:
Model No.: _____________________
Date Code: _____________________
Retain these numbers for
future reference.
When using tools,
basic precautions
should always be followed, including
the following:
CALIFORNIA PROPOSITION 65
This product or
its power cord may
contain chemicals known to the State
of California to cause cancer and birth
defects or other reproductive harm.
Wash hands after handling.
You can create dust when
you cut, sand, drill or grind
materials such as wood,
paint, metal, concrete, cement, or other
masonry. This dust often contains
chemicals known to cause cancer, birth
defects, or other reproductive harm.
Wear protective gear.
Finishing Nailer

Summary

Product Description

Nailer Features

Describes the key features of the finishing nailer.

Safety Instructions

Important Safety Information

Explains safety symbols and general warnings.

California Proposition 65

Warning regarding chemicals and reproductive harm.

General Safety

General safety precautions for operating the tool.

Work Area Safety

Precautions to ensure a safe working environment.

Personal Safety

Guidelines for user's personal safety during operation.

Tool Components and Specifications

Tool Use and Care

General Tool Usage

Safe practices for operating the tool.

Maintenance and Storage

Guidelines for tool upkeep and proper storage.

Service and Repair

Information on professional servicing and parts.

Air Source and Lubrication

Air Source Requirements

Specifications for the compressed air supply.

Lubrication Procedure

Instructions for lubricating the tool.

Operational Modes and Adjustments

Operational Mode - Single Cycle

Explanation of the single-cycle trigger operation.

Work Contact Element (WCE) Check

Procedure for checking the WCE trip mechanism.

Loading;Unloading the Nailer

Steps for safely loading and unloading fasteners.

Adjusting Nail Penetration

How to adjust fastener depth.

Adjusting Exhaust Direction

How to change the direction of the exhaust.

User Maintenance Instructions

Clearing a Jam

Step-by-step guide to clear jammed fasteners.

Technical Service

Contact information for technical support.

Fastener and Replacement Parts

Information on compatible fasteners and parts.

Assembly Procedure for Seals

Instructions for cleaning and lubricating seals.

Storage

Recommended storage conditions for the tool.

Troubleshooting Chart

Limited Warranty

Campbell Hausfeld CHN20103 Specifications

General

Brand	Campbell Hausfeld
Model	CHN20103
Category	Nail Gun
Language	English