Campbell Hausfeld Brad Nailer CHN70200 User Manual (English)

Questions and Answers:

R
Reginald BrennanJul 28, 2025
Why does my Campbell Hausfeld Nail Gun skip nails?
- S
  Stacey AlexanderJul 28, 2025
  If your Campbell Hausfeld Nail Gun skips driving nails, several factors could be at play. It might be due to a worn bumper, dirt in the nose piece or magazine, a damaged pusher spring, inadequate airflow, a worn O-ring on the piston, a damaged O-ring on the trigger valve, or air leaks. Try the following: * Replace the bumper. * Clean the drive channel and magazine. * Replace the spring or piston seals. * Check the fitting, hose, and compressor for adequate airflow. * Tighten any loose screws and fittings.
A
Angel OrtizAug 1, 2025
What to do if my Campbell Hausfeld Nail Gun runs slow?
- S
  Steven StewartAug 1, 2025
  If your Campbell Hausfeld Nail Gun is experiencing a loss of power or running slowly, it could be due to insufficient lubrication, a broken spring in the cylinder cap, or a blocked exhaust port in the cap. Try lubricating the nailer first. If that doesn't solve the issue, consider replacing the spring or any other damaged internal parts.
D
David HarmonAug 5, 2025
How to fix jammed nails in Campbell Hausfeld Brad Nailer CHN70200?
- D
  David HinesAug 5, 2025
  If nails are jammed in your Campbell Hausfeld Nail Gun, it could be due to several reasons: a worn guide on the driver, incorrect nail type, bent nails, loose magazine or nose screws, a damaged driver, or incorrect nail loading. To resolve this: * Replace the guide or driver if worn or damaged. * Ensure you are using the recommended nails and that they are not bent. * Tighten any loose magazine or nose screws.
S
sabrinajacksonAug 10, 2025
What to do if Campbell Hausfeld Brad Nailer CHN70200 Nail Gun leaks air between housing and cap?
- P
  Peter StanleyAug 10, 2025
  If you notice air leaking between the housing and cap of your Campbell Hausfeld Nail Gun, the issue might be due to loose screws or a damaged gasket. Try tightening the screws first. If the leak persists, replace the gasket.
D
Daniel CaseyAug 14, 2025
How to fix air leaking at trigger valve on Campbell Hausfeld Nail Gun?
- A
  Andrew SmithAug 14, 2025
  If you're experiencing air leaks at the trigger valve of your Campbell Hausfeld Nail Gun, it's likely that the O-rings in the trigger valve housing are damaged. Replace the O-rings and also check the operation of the Work Contact Element (WCE).
J
Jennifer RobinsonAug 18, 2025
Why is my Campbell Hausfeld Nail Gun leaking air between housing and nose?
- O
  orobertsAug 19, 2025
  If you notice air leaking between the housing and nose of your Campbell Hausfeld Nail Gun, it could be due to damaged O-rings and/or seals, or damage to the bumper. Replace the O-rings and/or seals. If the problem continues, replace the bumper.
A
Angela LeeAug 22, 2025
What to do if laser and low nail indicators are not working on Campbell Hausfeld Brad Nailer CHN70200?
- A
  Amanda JohnsonAug 22, 2025
  To address a non-functional laser or low nail indicator on your Campbell Hausfeld Nail Gun, ensure the system power switch is turned on. If it is on, replace the batteries. Also, ensure components were properly replaced during re-assembly after customer maintenance. Check that the WCE is slightly depressed.

Campbell Hausfeld Brad Nailer CHN70200 Specifications

General

Type	Brad Nailer
Model Number	CHN70200
Power Source	Pneumatic
Fastener Type	Brad Nails
Fastener Gauge	18 gauge
Magazine Capacity	100 nails
Nail Gauge	18
Air Inlet	1/4 inch NPT
Depth Adjustment	Yes, Tool-Free