Campbell Hausfeld PW150100

Questions and Answers

B
Brittany ArmstrongAug 13, 2025
What to do if my Campbell Hausfeld Pressure Washer does not start up?
- C
  Courtney PhelpsAug 14, 2025
  If your Campbell Hausfeld Pressure Washer doesn't start up, first, push the reset button on the GFCI plug. If that doesn't work, check the plug, socket, and fuses to ensure they are properly connected and functioning. Avoid using an extension cord, as it may be the cause. Also, confirm that the main voltage supply is adequate. If the thermal safety switch has tripped, switch off the unit and allow the motor to cool down.
D
Diane DawsonAug 18, 2025
How to fix low pressure on a Campbell Hausfeld PW150100 Pressure Washer?
- J
  jamesrichardsonAug 18, 2025
  If your Campbell Hausfeld Pressure Washer has low pressure or the pump runs rough, it could be due to several reasons. A worn nozzle can cause this, so replace it. The inlet filter on the pump might be clogged, so clean it and check it more frequently. A restricted inlet, such as a collapsed or kinked garden hose, can also be the cause, so check the hose and inlet water flow. Additionally, a leaking high-pressure hose can lead to low pressure, so replace the hose if necessary. Finally, ensure all hoses and fittings are tight to prevent the pump from drawing in air.
K
Kelly JohnsonAug 21, 2025
Why is the pressure fluctuating on my Campbell Hausfeld PW150100?
- J
  Julie CookAug 21, 2025
  If your Campbell Hausfeld Pressure Washer has fluctuating pressure, make sure that hoses and fittings are tight and purge air from the garden hose, as the pump might be drawing in air. Also, the nozzle might be clogged, so clean or replace it.
J
Jillian RuizAug 26, 2025
Why does my Campbell Hausfeld PW150100 Pressure Washer pressure drop after use?
- M
  mark46Aug 26, 2025
  If your Campbell Hausfeld Pressure Washer's pressure drops after a period of normal use, the nozzle may be worn. Inspect the nozzle and replace it if necessary.
M
Melissa FrankAug 28, 2025
Why does my Campbell Hausfeld PW150100 Pressure Washer motor stop suddenly?
- S
  Shannon BrownAug 28, 2025
  If the motor of your Campbell Hausfeld Pressure Washer stops suddenly, remove any extension cord being used, as the product cannot be used with one. Also, the thermal safety switch may have tripped due to overheating. In this case, check that the main supply voltage corresponds to the product's specifications.
J
Judy VillarrealSep 1, 2025
Why is my Campbell Hausfeld PW150100 Pressure Washer pump so noisy?
- W
  wcooperSep 1, 2025
  If your Campbell Hausfeld Pressure Washer pump is noisy or runs rough, ensure that all fittings are tight and increase water pressure, as the pump may be drawing in air or there's a low water supply. Also, reduce the water temperature if it is above 100° F.
M
melissadukeSep 5, 2025
How to fix my Campbell Hausfeld Pressure Washer that will not spray detergent?
- V
  Vanessa SchmidtSep 5, 2025
  If your Campbell Hausfeld Pressure Washer is not spraying detergent, try changing the nozzle and detergent dispenser.
D
Derrick PattersonSep 9, 2025
What to do if my Campbell Hausfeld PW150100 motor will not start?
- F
  fwatkinsSep 9, 2025
  If your Campbell Hausfeld Pressure Washer motor will not start, turn the water supply off, then disconnect the garden hose and the black high-pressure hose from the unit to relieve any pressure from the pump. If your unit has a GFCI plug, push the top button, then the bottom button, and then the top button again. A light should appear in the small window above the buttons. If there is no red light, the unit is not getting power and may need to be taken to a service center for repair.