Need help?Do you have a question about the Canon imageRUNNER ADVANCE 4045 and is the answer not in the manual?
Fixing temperature detected by main thermistor does not rise.
Main thermistor reading is 250 deg C or more continuously for 200 msec.
Hardware circuit detects overheating of main or sub thermistor for 30 msec.
Sub thermistor reading is 295 deg C or more continuously for 200 msec.
Main thermistor reading is less than 115 deg C continuously for 400 msec.
Low fixing temperature detected after standby.
Thermistor disconnection detected with connector for 30 sec continuously.
Main motor drive detection signal absent for 2 sec after rotation start.
Fixing motor drive detection signal absent for 2 sec after rotation start.
Path between sub hopper and developing assembly clogged with toner.
Developing Assembly Toner Sensor connection signal absent for 100 msec.
Developing Assembly Toner Sensor ON counter error.
Sub Hopper Toner Sensor disconnected.
Disconnection status of bottle motor detected 15+ times continuously.
Detection of open circuit of count pulse signal.
Polygon Motor speed lock signal does not indicate locked state.
Polygon Motor speed lock signal indicates deviation 10 times.
Polygon Motor speed lock signal does not indicate locked state for 6.5 sec.
EEPROM access error: 20 retries failed during communication.
Main ROM reading or writing error occurs.
Option ROM reading or writing error occurs.
Timeout error between DC Controller PCB and Main Controller PCB.
Communication error with image PCB (Serial communication error).
Error in CCD home position detection.
Codec error: JBIG encode error.
Codec error: JBIG decode error.
Codec error: Soft decode error.
Codec error: ROTU hardware error.
Codec error: ROTU timeout error.
Codec error: MemFill hardware error.
Release motor HP sensor does not change within specified period.
Not proper DADF is installed.
Communication with host machine interrupted.
Communication between Saddle Controller and Finisher Controller suspended.
Checksum data for EEPROM on finisher controller PCB has an error.
Checksum data for EEPROM on punch controller PCB has an error.
Stapler does not leave rear end assist home position when motor driven.
Stapler does not return to rear end assist home position when motor driven.
Shift motor fails to move from Home Position.
Aligning plate does not leave home position sensor when motor driven.
Stapler does not leave staple home position when motor driven.
Stapler does not return to staple home position when motor driven.
STP Move Motor fails to move from Home Position.
Stapler does not leave shift home position when shift motor driven.
Swing home position error.
Stapler does not return to swing home position when swing motor driven.
Aligning plate does not leave rear home position sensor when motor driven.
Tray 1 does not return to home position or move to other area.
Tray Lift Motor unable to complete operation.
Tray 1 does not return to home position when shift motor driven.
Dangerous area reached before paper surface sensor detects paper.
Swing guide or staple safety switch activated while tray operating.
FG input cannot be detected when tray 1 shift motor driven.
Lock detection signal turns OFF 150 ms after turned ON.
Lock detection signal does not turn ON when shift motor driven.
Lock detection signal does not turn OFF when tray 1 shift motor is at stop.
Tray 1 does not return to home position or move to other area.
Upper limit area reached before tray 2 paper surface sensor detects paper.
FG input cannot be detected when tray 2 shift motor driven.
Shift Roller Release Motor fails to move from Home Position.
Entrance Roller Motor fails to move from Home Position.
Entrance Roller Motor fails to return to Home Position.
Gripper Open/Close Motor fails to move from Home Position.
Puncher does not detect home position sensor when motor driven.
Puncher does not detect home position sensor after motor stopped.
Low light voltage received even when light emitting duty increased.
Light voltage received when light emitting duty decreased to 0%.
Low light voltage received even when light emitting duty increased.
Light voltage received when light emitting duty decreased to 0%.
Low light voltage received even when light emitting duty increased.
Low light voltage received even when light emitting duty increased.
Light voltage received when light emitting duty decreased to 0%.
Low light voltage received even when light emitting duty increased.
Light voltage received when light emitting duty decreased to 0%.
Low light voltage received even when light emitting duty increased.
Light voltage received when light emitting duty decreased to 0%.
Punch slide unit does not leave horizontal home position sensor.
Punch slide unit does not return to horizontal home position sensor.
Paper positioning plate home position sensor does not turn ON.
Paper positioning plate home position sensor does not turn OFF.
Feed speed of paper fold roller reaches 5 mm/sec or less.
Status of Paper Fold Home Position Sensor does not change.
Guide home position sensor does not turn ON when guide motor driven.
Guide home position sensor does not turn OFF when guide motor driven.
Aligning plate home position sensor does not turn ON when motor driven.
Aligning plate home position sensor does not turn OFF when motor driven.
Stitcher home position sensor does not turn ON when stitch motor driven.
Stitcher home position sensor does not turn OFF when stitch motor driven.
Stitcher home position sensor does not turn ON when stitch motor driven.
Fixing main thermistor detects 230 degC or higher.
Fixing main thermistor detects hardware overheating.
Abnormal temperature difference among thermistors detected.
Fixing Assembly temperature rise error.
Fixing Cleaning Web absent, pulled out 2000 times.
Fixing Cleaning Web Drive Solenoid connection not detected.
Drum Motor lock error.
Waste Toner Lock Detection Switch detects locked state 3 times.
Waste Toner Lock Detection Switch detects locked state 3 times.
Fixing Motor lock error.
Developing Assembly toner was empty for 2 minutes.
Developing Assembly Cleaning Scraper displacement state detected.
Developing Toner Sensor connection detection port was OFF.
Developing Motor lock error.
Buffer Toner Sensor connection detection port was OFF.
Magnet Roller Clutch connection cannot be detected 5 times.
Toner Excess Supply Sensor connection detection port was OFF.
Magnet Roller Clutch connection detection port was OFF.
Communication with Puncher unit is interrupted.
Checksum for EEPROM data has an error.
Checksum for EEPROM data has an error.
Stapler does not leave rear end assist home position when motor driven.
Folding Feed Motor lock signal detected for more than specified time.
Gear Change Home Position Sensor does not turn ON when motor driven.
Gear Change Home Position Sensor does not turn OFF when motor driven.
Aligning plate does not leave front home position sensor when motor driven.
Aligning plate does not return to front home position sensor when motor driven.
Stapler does not leave staple home position when motor driven.
Stapler does not leave shutter home position when motor driven.
Guide home position sensor does not turn ON when guide motor driven.
Guide home position sensor does not turn OFF when guide motor driven.
General| Print Speed | 45 ppm |
|---|---|
| Print Resolution | 1200 x 1200 dpi |
| Monthly Duty Cycle | 150, 000 pages |
| Duplex Printing | Yes |
| Memory | 2 GB |
| Hard Disk Drive | 160 GB |
| Functions | Print, Copy, Scan, Fax |
| Operating System Compatibility | Windows, Mac, Linux |
| Connectivity | Ethernet, USB 2.0 |
| Document Feeder | 100 sheets |
| Warm-up Time | Less than 30 seconds |
| Standard Paper Capacity | 1, 180 sheets (Std. 550-sheet x 2 cassettes, 80-sheet bypass) |
To Next Page