Cardinal Gates STAIRWAY SPECIAL - User Manual

A
B
C
E
F
G
J
I
1
6 ”
A
C or J
2
C or J
3
2X
E
4
B
F
I
5
LOOSEN AT TOP AND
BOTTOM OF GATE TO
ADJUST GATE WIDTH
2X
G
6
K
H
ONE-WAY
STOP BRACKET
OPTION
ASSEMBLY INSTRUCTIONS
2. Install second
screw (C) in
top of hinge
bracket
securing it to
the wall.
NOTE: THIS SIDE OF GATE HAS
THREE (3) HOLES - ONLY USE TOP AND
BOTTOM HOLES FOR THIS STEP
3. Insert eye bolts with nut and washer (E)
into top and bottom of hinge side gate
(side with three holes). Be sure nuts are
tight. Do not use middle hole for this step.
4. Hang gate by inserting hinge rod (B), through top
of mounted hinge bracket (A), through upper plastic
shoulder washer (F), through both eye bolts, through
lower plastic shoulder washer (F), and finally through
bottom of hinge bracket. To secure hinge, insert
key ring (I) through hole in end of hinge rod. Gate
can be mounted at angles up to 30 degrees.
5. Use Allen wrench (G) to unscrew
set screws on top and bottom of
gate to extend gate. LEAVE
SHIPPING TABS IN PLACE TO NOT
MAR GATE FINISH. You will remove
shipping tabs during final tightening.
6. Mount latch assembly (K) to gate using 3/4” bolts with serrated
washers (D). Attach wall mount for latch assembly (H) up
into part (K) that is now secure on gate. Slide gate out to
mark holes for (K) on attaching wall. (*OPTIONAL ONE WAY
BRACKET INSTALLED HERE) Then attach the wall mount of
latch assembly to wall using Phillips head screws (C). Optional
long screws (J) maybe be used to attach gate to stud through
dry wall.
GATE IS RECOMMENDED FOR CHILDREN BETWEEEN 6 AND 24 MONTHS.
STAIRWAY SPECIAL - MODEL SS30
D
H
K
L
ONE-WAY
STOP BRACKET
OPTION
D
D
ONE-WAY
STOP BRACKET
OPTION
L
IF GATE IS INSTALLED AT TOP OF STAIRCASE:
Install one-way stop bracket (L) on one side of
wall mount latch to have gate open in only one
direction for maximum safety.
FOR OPENINGS 27” (68cm) - 42.5” (108cm)
SEE REVERSE
FOR GATE
OPERATION
INSTRUCTIONS
1. Install hinge bracket
(A) to wall (stationary
side of gate) using
Phillips screw (C)
beginning 6 ” above
floor surface. (Use
ruler on left edge of
this sheet to measure
from floor).
OPTION: Long
screws (J) maybe be
used to attach gate to
stud through dry wall.

Summary

Assembly Instructions

Install Hinge Bracket

Install the hinge bracket (A) to the wall, beginning 6½" above the floor surface.

Secure Hinge Bracket

Install the second screw (C) into the top of the hinge bracket to secure it to the wall.

Install Gate Eye Bolts

Insert eye bolts (E) with nut and washer into the top and bottom of the hinge side gate.

Hang Gate on Hinge Rod

Hang the gate by inserting the hinge rod (B) through the mounted hinge bracket and eye bolts.

Adjust Gate Width

Use Allen wrench (G) to unscrew set screws on the top and bottom of the gate to extend.

Mount Latch Assembly

Mount the latch assembly (K) to the gate and attach the wall mount for the latch assembly.

Staircase Installation Safety

Install one-way stop bracket (L) on one side of wall mount latch for safety at top of staircase.

General Safety Warning

Warning regarding child safety, proper installation, and use of the gate.

Gate Operation

Opening the Gate

Instructions on how to open the gate using the flip latches with your thumb and index finger.

Closing the Gate

Instructions on how to close the gate by lifting and aligning latch pins with bracket holes.

Latch Operation Reminder

Reminder to use the right hand for latch to the left and left hand for latch to the right.

Gate Maintenance

Gate Care & Reminders

Gate Warranty

Warranty Terms

Details the one-year warranty for home use and 90-day warranty for commercial use.

Exercising the Warranty

Instructions on how to ship the gate for repair or replacement under warranty.

Customer Assistance

Cardinal Gates STAIRWAY SPECIAL Specifications