Cardinal Health CAX1230FA

Questions and Answers

R
Robert RodriguezAug 18, 2025
How to troubleshoot a Cardinal Health Laboratory Equipment unit that does not operate?
- C
  Carol TurnerAug 18, 2025
  If the Cardinal Health Laboratory Equipment unit does not operate or the Power Failure Indicator is on, first, ensure the power cord is securely plugged into the outlet. Test the outlet with another appliance to confirm it is working. Verify the double pole circuit breaker, located next to the power inlet, is in the “ON” position (“I”). Try cycling the switch to the OFF position (“O”) and then back to ON (“I”). Check the voltage to ensure it is correct for your unit. If the outlet is dead, inspect the circuit breaker or fuses. Note that the unit should not be connected to a GFCI protected outlet.
S
Sheila NewtonAug 20, 2025
What to do if there is condensation around the door frame of Cardinal Health CAX1230FA Laboratory Equipment?
- C
  Charles PalmerAug 20, 2025
  If you see condensation around the door frame of your Cardinal Health Laboratory Equipment, you can try the following: Increase the Perimeter Heater Duty Cycle. Ensure all port holes in the cabinet top, sides, and back are properly sealed to prevent warm airflow into the cabinet, and seal any gaps. Check that nothing, such as a sensor, is obstructing the door seal. Inspect the door seal for any damage.
J
Joyce DicksonAug 23, 2025
Why is my Cardinal Health CAX1230FA unit warming up?
- J
  jerry54Aug 23, 2025
  If your Cardinal Health Laboratory Equipment unit warms up, ensure the door is completely closed. Inspect the door seal. Allow sufficient time for the unit to recover after loading warm product. Check for proper voltage to the unit, and if there is no voltage, call an electrician. If needed, adjust the setpoint. If there is an extended air leak into the freezer, manually defrost the unit by turning it off to allow all frost and ice to melt.
W
William HamptonAug 26, 2025
How to stop temperature fluctuations in Cardinal Health CAX1230FA Laboratory Equipment?
- M
  Michael StoneAug 26, 2025
  If the temperature fluctuates in your Cardinal Health Laboratory Equipment, ensure the temperature control is set correctly. Make sure the condenser and filter are clean. Check that the solution bottles for the temperature sensors are full, using a 50/50 mixture of glycerine and distilled water. If the issue persists after checking these, contact an authorized service representative.
L
leachlauraAug 28, 2025
What does "E02" mean on a Cardinal Health Laboratory Equipment display?
- J
  James RamirezAug 28, 2025
  If the display on your Cardinal Health Laboratory Equipment shows “E02”, this indicates a Control Probe Failure. Check for a loose probe connector and replace the control probe.
K
karenmooreAug 30, 2025
What does "E03" mean on a Cardinal Health CAX1230FA Laboratory Equipment display?
- T
  Tiffany EatonAug 31, 2025
  If the display on your Cardinal Health Laboratory Equipment shows “E03”, this indicates a Defrost Probe Failure. Check for a loose probe connector and replace the defrost probe.
B
bullockcarolSep 2, 2025
What does "E05" mean on a Cardinal Health Laboratory Equipment display?
- E
  Erika AlvarezSep 2, 2025
  If the display on your Cardinal Health Laboratory Equipment shows “E05”, this indicates an Ambient Probe Failure. Check for a loose probe connector and replace the ambient probe.
L
Laura SalinasSep 4, 2025
What does "E06" mean on a Cardinal Health CAX1230FA Laboratory Equipment display?
- B
  Benjamin SchmittSep 4, 2025
  If the display on your Cardinal Health Laboratory Equipment shows “E06”, this indicates a Drip Pan Probe Failure. Check for a loose probe connector and replace the drip pan probe.
J
John PerezSep 7, 2025
What does “Err” mean on a Cardinal Health Laboratory Equipment display?
- N
  Nathan CruzSep 7, 2025
  If the display on your Cardinal Health Laboratory Equipment shows “Err”, this indicates an Upper Bottle Probe Failure. Check for a loose probe connector and replace the upper bottle probe.
M
Mark TorresSep 9, 2025
What does error code "E01" mean on Cardinal Health Laboratory Equipment?
- F
  foxstephanieSep 10, 2025
  If the display on your Cardinal Health Laboratory Equipment shows “E01”, it means there is an Invalid Algorithm. Check to ensure the model type is set correctly in service mode.