Cardinal Health CAX3030FA

Questions and Answers

G
ghughesAug 18, 2025
How to troubleshoot a Cardinal Health CAX3030FA unit that does not operate?
- J
  Joseph WashingtonAug 18, 2025
  If the Cardinal Health Laboratory Equipment unit does not operate or the Power Failure Indicator is on, first, ensure the power cord is securely plugged into the outlet. Test the outlet with another appliance to confirm it is working. Verify the double pole circuit breaker, located next to the power inlet, is in the “ON” position (“I”). Try cycling the switch to the OFF position (“O”) and then back to ON (“I”). Check the voltage to ensure it is correct for your unit. If the outlet is dead, inspect the circuit breaker or fuses. Note that the unit should not be connected to a GFCI protected outlet.
J
John WhitakerAug 21, 2025
What to do if there is condensation around the door frame of Cardinal Health Laboratory Equipment?
- B
  bponceAug 21, 2025
  If you see condensation around the door frame of your Cardinal Health Laboratory Equipment, you can try the following: Increase the Perimeter Heater Duty Cycle. Ensure all port holes in the cabinet top, sides, and back are properly sealed to prevent warm airflow into the cabinet, and seal any gaps. Check that nothing, such as a sensor, is obstructing the door seal. Inspect the door seal for any damage.
K
Kevin LopezAug 23, 2025
Why is my Cardinal Health Laboratory Equipment unit warming up?
- R
  Roy LeeAug 23, 2025
  If your Cardinal Health Laboratory Equipment unit warms up, ensure the door is completely closed. Inspect the door seal. Allow sufficient time for the unit to recover after loading warm product. Check for proper voltage to the unit, and if there is no voltage, call an electrician. If needed, adjust the setpoint. If there is an extended air leak into the freezer, manually defrost the unit by turning it off to allow all frost and ice to melt.
J
johnstoncarmenAug 26, 2025
How to stop temperature fluctuations in Cardinal Health CAX3030FA?
- M
  Mackenzie JacksonAug 26, 2025
  If the temperature fluctuates in your Cardinal Health Laboratory Equipment, ensure the temperature control is set correctly. Make sure the condenser and filter are clean. Check that the solution bottles for the temperature sensors are full, using a 50/50 mixture of glycerine and distilled water. If the issue persists after checking these, contact an authorized service representative.
J
James MarshAug 28, 2025
What does "E02" mean on a Cardinal Health Laboratory Equipment display?
- J
  jessica05Aug 28, 2025
  If the display on your Cardinal Health Laboratory Equipment shows “E02”, this indicates a Control Probe Failure. Check for a loose probe connector and replace the control probe.
C
Crystal BrownAug 30, 2025
What does "E03" mean on a Cardinal Health CAX3030FA Laboratory Equipment display?
- A
  Alejandro BuckleyAug 30, 2025
  If the display on your Cardinal Health Laboratory Equipment shows “E03”, this indicates a Defrost Probe Failure. Check for a loose probe connector and replace the defrost probe.
A
Anthony HillSep 2, 2025
What does "E05" mean on a Cardinal Health CAX3030FA display?
- T
  timothyhaleSep 2, 2025
  If the display on your Cardinal Health Laboratory Equipment shows “E05”, this indicates an Ambient Probe Failure. Check for a loose probe connector and replace the ambient probe.
L
Laura ChavezSep 4, 2025
What does "E06" mean on a Cardinal Health CAX3030FA Laboratory Equipment display?
- M
  Melanie HooperSep 5, 2025
  If the display on your Cardinal Health Laboratory Equipment shows “E06”, this indicates a Drip Pan Probe Failure. Check for a loose probe connector and replace the drip pan probe.
B
bairdjosephSep 7, 2025
What does “Err” mean on a Cardinal Health CAX3030FA display?
- J
  James SanchezSep 7, 2025
  If the display on your Cardinal Health Laboratory Equipment shows “Err”, this indicates an Upper Bottle Probe Failure. Check for a loose probe connector and replace the upper bottle probe.
T
Tracy KaufmanSep 9, 2025
What does error code "E01" mean on Cardinal Health Laboratory Equipment?
- M
  Matthew TrujilloSep 9, 2025
  If the display on your Cardinal Health Laboratory Equipment shows “E01”, it means there is an Invalid Algorithm. Check to ensure the model type is set correctly in service mode.