Carlton 2015 - SPECIFICATIONS

F:\data\John\Docs\Machine Docs\Machine Specs\2015 Apache SPECS 140 Deere.DOC
Carlton Apache 2015 Specifications
General: Hydraulic System:
Weight: 6820 Pounds Hyd Pump Displcmnt: 1.5 in cu/rev total from 2 pumps
Length: 211 inches Hyd Pump Drv Systm:Direct Drive off Engine Mount
Height: 100 inches Flow: 16 GPM Total Tandem Systems
Tires: 235/75R17.5 Ld Rng H 4805 # @125 PSI System Relief: 2500 PSI
Axle: Dexter Torflex 8,000 Pound Cap Oil Tank Capacity: 18 Gallons
Brakes: Electric with Breakaway Switch Oil Type: AW32
Hitch: Five Inch Height Adjustable Pintle Valve: DO5 Electric Solonoid
Fuel Capacity: 25 Gallons Hose: 16,000 PSI Burst - Exceeds SAE 100R2
Battery: 29HVD 950 CCA Oil Filter: 10 Micron Return with Suction Strainer
Jack Stand: 10000 # Cap Screw Type Swing Up
Engine: Drive System:
Manufacturer: John Deere Engine Sheave: 4/5V9.25
Number of Cylinders: Four Jackshaft Sheave: 4/5V11.80
Bore: 4.19 Inches (106 mm) Drive Belt: 4/5V1120
Stroke: 5.0 Inches(127 mm) Cutter Head Shaft: 3 ½ inches
Displacement: 276 Cubic Inches (4.5L)
Maximum RPM: 2400 RPM Feed System:
Horsepower: 140HP
Torque: 367 Ft Lbs (498 NM) Feed Motors: Dual 46 In Cu Top 32 In Cu Bottom
Cooling Medium: Liquid Water/Antifreeze Mixture Flow: Separate Systems for Top/Btm Feed
Air Cleaner: Two Stage Dry Type Hydraulic Drive: Live – Driven off engine
Oil Filter: Full Flow Spin On Autofeed: Reversing, Digital, Fully Adjustable
Oil Capacity: 13 Quarts Feed Rate: 110 Feet Per Minute
Oil Type: John Deere Feed Rollers: Top: 15 ¾” Dia Bottom: 10 ½” Dia
Electrical: 12 Volt Springs: Two 30” Tight Wound Powder Coated
Gauges: Powerview Feed Pivot Bearings: Two 2” Tapered Roller
Clutch: Twin Disk 11 ½” Over Center Lift Cylinders: Two 2” x 16” with 1” attachments
Discharge: Crank Adjustable Swivel and Height
Bearings: Frame:
Drum Bearings: 2 15/16 inches Tapered Roller Main Trailer Tongue: 3”x 6” with 3/8” wall
Feed Roller Bearings: 2 inches Ball Bearing Main Trailer Frame: 2”x6” with 3/16” wall
Drum Shaft: 3 ½ inches Telescoping Tongue: N/A
Feed Roller Shaft: 2 inches Engine Channel Mnts: 4” Channel with 5/16”
web
Infeed Chute: 3/16” with 2”x2”x1/4” tube frame
Infeed Tray: 3/16” Plate w 2”x2” and 2” x 4” Tube
Chipper Drum: Folding Tray Lock: N/A
Discharge Chute: 12 gauge
Drum Diameter: 24 inches Discharge Lock: ¾” Spring Loaded Pin
Drum Width w/Fans: 27 inches Fuel Tank: High Density Polyethylene
Drum Balance: Precision High Speed Balanced Hydraulic Tank: 10 gauge with baffles rubber mtd
Drum Speed: 1160 RPM Battery Box: 10 gauge - lockable
Number of Knives: 2 Fenders: 3/16” checker plate
Knife Dimensions: 10 1/2” x 5 ½” x 5/8” Feeder Bar: 1 ½” OD x 1/8” wall - removable
Anvil: 3 1/2” x 20” x ½” AR400 Radiator Guards: N/A
Drum Fans: 12 ¼” x 2 1/2” x 6.75” Light Brackets: 3/16” with hidden wiring
Hitch Plate: ¾” Plate adjustable 5” Up/Down
Cutting Dimensions:
Throat Opening: 15” x 20”