Carrier 23XL - Table 18 - 23 XL Compressor Torque Specification Chart for Metric amd American Fasteners

95
Table 18 — 23XL Compressor Torque Specification Chart for Metric amd American Fasteners
ITEM
CAP SCREW
SIZE AND TYPE
GRADE ASSEMBLY LOCATION
TORQUE
Nm Lb-Ft Lb-in.
CAP SCREW
M5 X 0.8 X 12 S.H.
10.9
1. FUSITE-MOTOR CASING
2. SLIDE SEAL RETAINER-CYLINDER STOP
4.1-5.4 3-4 36-48
M6 X 1 X 16 S.H.
1. CONTROL VALVES-SLIDE CASING
2. SLIDE SEAL ADAPTOR-SEPARATOR PLATE
(FRAME 1 AND 2 ONLY)
3. SLIDE SEAL ADAPTOR-SLIDE CASING PLUG
(FRAME 4 ONLY)
6.8-9.6 5-7 60-84
M10 X 1.5 X 35 H.H.
1. BRG RETAINER-MALE ROTOR
2. BRG RETAINER-FEMALE ROTOR
41-47 30-35 N/A
M10 X 1.5 X 40 S.H.
1. SLIDE VALVE COVER-SLIDE CASING
2. SLIDE CASING-SEPARATOR PLATE (TC FRAME 1
AND 2 ONLY)
61-68 45-50 N/A
M10 X 1.5 X 50 H.H. MOTOR ROTOR-MALE ROTOR 20-27 15-20 N/A
M12 X 1.75 X 40 S.H. SERVICE VALVE PAD-MOTOR COVER 103-115 75-85 N/A
M12 X 1.75 X 50 S.H.
TC FRAME 1 AND 2 ONLY
1. MOTOR COVER-MOTOR CASING
2. SEPARATOR PLATE-OUTLET CASING
3. DISCHARGE COVER-OUTLET CASING
103-115 75-85 N/A
M12 X 1.75 X 60 S.H.
1. MOTOR END PLATE-MOTOR COVER-MOTOR CAS-
ING (FRAME 1 AND 2 ONLY)
2. MOTOR COVER-MOTOR CASING (TD FRAME 4
ONLY)
3. SLIDE CASING-OUTLET CASING (TD FRAME 4
ONLY)
M12 X 1.75 X 70 S.H.
TD FRAME 4 ONLY
MOTOR END PLATE-MOTOR COVER-MOTOR CASING
M12 X 1.75 X 80 S.H.
TC FRAME 1 AND 2 ONLY
SLIDE CASING-SEPARATOR PLATE-OUTLET CASING
M12 X 1.75 X 90 S.H.
TD FRAME 4 ONLY
SLIDE CASING (BOTTOM)-OUTLET CASING
FRAME 1 AND 2
M16 X 2 X 55 S.H.
FRAME 4
M16 X 2 X 70 S.H.
1. ROTOR CASING-INLET CASING AND OUTLET
CASING
2. MOTOR CASING-INLET CASING
3. OPEN DRIVE END COVER-INLET CASING
4. DISCHARGE COVER-OUTLET CASING
(TD FRAME 4 ONLY)
252-280 185-205 N/A
M20 X 2.5 X 70 S.H.
INLET FLANGES-INLET CASING (TC FRAME 1 AND 2
ONLY)
485-513 355-375 N/A
M22 X 2.5 X 80 S.H.
TD FRAME 4 ONLY
INLET FLANGES-INLET CASING
697-724 510-530 N/A
SET SCREW
M10 X 1.5 X 16 S.S.
10.9
TD FRAME 4 ONLY
OPEN DRIVE SEAL ADAPTER
41-47 30-35 N/A
M10 X 1.5 X 30 S.S. STATOR KEY LOCK 13-20 10-15 120-180
PIPE PLUG
1
/
8
NPTF
N/A
INLET CASING 20-27 15-20 180-240
1
/
4
NPTF
TD FRAME 4 ONLY
SLIDE CASING
27-34 20-25 240-300
HEX PLUG
7
/
16
-20
N/A
1. INLET CASING
2. SLIDE CASING
13-16 10-12 130-140
9
/
16
-18
1. MOTOR CASING
2. OUTLET CASING
3. ROTOR CASING
4. SLIDE CASING
23-26 17-19 210-230
3
/
4
-16
1. OUTLET CASING
2. SLIDE CASING (TC FRAME 1 AND 2 ONLY)
60-65 44-48 530-570
1
1
/
16
-12
1. INLET CASING
2. ROTOR CASING
3. OUTLET CASING
112-125 83-92 1000-1100
1
3
/
16
-12
TD FRAME 4
OUTLET CASING
125-140 92-103 1100-1240
TERMINAL PIN
5
/
8
-11
N/A
1. TERMINAL NUTS
2. MOTOR LEAD
23-26 17-19 N/A
1
3
/
16
-12
1. TERMINAL PIN BODY
2. MOTOR CASING
27-34 20-25 N/A
LOCKNUT
M20 X 1
N/A
SLIDE VALVE ASSEMBLY 68-75 50-55 N/A
M35 X 1.5 SLIDE VALVE ASSEMBLY 95-102 70-75 N/A
RELIEF VALVE 1
5
/
8
-12 UN-2A N/A ROTOR CASING 345-379 254-279 N/A
PLUG, ORIFICE M8 X 1.25 N/A
1. INLET CASING
2. OPEN DRIVE END COVER (TC FRAME 1 AND 2
ONLY)
19-24 14-18 168-216
WAFER HEAD SCREW M6 X 1 N/A
TD FRAME 4 ONLY
SLIDE VALVE ASSEMBLY
13-15 10-11 120-130