113
APPENDIX C: Navigatort Display
MODE -- CONFIGURATIONS (cont)
ITEM EXPANSION RANGE UNIT DEFAULT POINT
NET (cont) Building Net Config Menu
SYST System To uch Menu
D.ST System Touch Device Inst 0 to 4194303 160099 DEVST
ST.PL System Touch Poll Rate 10 to 60 sec 10 POLLST
AI.ST System Touch AI for SPT 0 to 9999 1 AISTSPT
AI.SR System Touch AI for SPRH 0 to 9999 4 AISTSPRH
LINK LINKAGE SETTINGS MENU
D.IAQ BACnet device for IAQ 0 to 4194303 1610100 DEVIAQ
O.IAQ Object instance for IAQ 0 to 9999 1009 OBJIAQ
C.IAQ Change of value for IAQ 0to60 0 COVIAQ
D.OAQ BACnet device for OAQ 0 to 4194303 1610100 DEVOAQ
O.OAQ Object instance for OAQ 0 to 9999 285 OBJOAQ
C.OAQ Change of value for OAQ 0to60 0 COVOAQ
D.ORH BACnet device for OARH 0 to 4194303 1610100 DEVOARH
O.ORH Object instance for OARH 0 to 9999 1022 OBJOARH
C.ORH Change of value for OARH 0to60 0 COVOARH
D.OAT BACnet device for OAT 0 to 4194303 1610100 DEVOAT
O.OAT Object instance for OAT 0 to 9999 1003 OBJOAT
C.OAT Change of value for OAT 0to60 0 COVOAT
D.RRH BACnet device for RARH 0 to 4194303 1610100 DEVRARH
O.RRH Object instance for RARH 0 t o 9999 30 OBJRARH
C.RRH Change of value for RARH 0to60 0 COVRARH
D.RAT BACnet device for RAT 0 t o 4194303 1610100 DEVRAT
O.RAT Object instance for RAT 0 to 9999 1010 OBJRAT
C.RAT Change of value for RAT 0to60 0 COVRAT
D.SPT BACnet device for SPT 0 to 4194303 1610100 DEVSPT
O.SPT Object instance for SPT 0 to 9999 2007 OBJSPT
C.SPT Change of value for SPT 0to60 0 COVSPT
LCLS Allow Local Sched Edit Yes/No No LCL_EDIT
ZSSC ZS Sensor Configuration
Z1.AD Zone Sensor 1 Address 0 to 255 255 ZSADDR1
Z2.AD Zone Sensor 2 Address 0 to 255 255 ZSADDR2
Z3.AD Zone sensor 3 address 0 to 255 255 ZSADDR3
Z4.AD Zone sensor 4 address 0 to 255 255 ZSADDR4
Z5.AD Zone sensor 5 address 0 to 255 255 ZSADDR5
Z.PR Zone sensor poll rate 1 t o 100 sec 5 ZSPOLLRT
Z.UT Zone sensor unit 0=degree F 0=degree F ZSUNIT
Z.FUE ZS Force Unoccup enable No No ZSFUNEN
Z.FUD ZS Force unocc wt delay No No ZSTL SOC
Z.TCE ZS TLO Cont Enable No No ZSTLOEN
Z.TSO ZS TLO set during occ No No ZSTLSOC
Z.UIM Zone sensor UI Mode 1=Dual Offsets 1=Dual Offsets ZSUIM
DISP User Display Config Menu
METR Metric Display Ye s/No No DISPUNIT
LANG Display Language Select 0=English 0=English LANGUAGE
PROT User Password Protection Enable/Disable Enable PASS_EBL
PSWD User Password 0 t o 9999 1111 PAS SWORD
To Next Page
Loading...
