Why does nothing appear on my Casio Label Maker display?
If nothing appears on the Casio Label Maker display, it could be due to low batteries. Try replacing them. Alternatively, the batteries might be loaded incorrectly. Remove them and reload them correctly, ensuring they are properly aligned.
What to do if tape does not come out of Casio KL-100E?
If the tape doesn't come out when you press PRINT on your Casio Label Maker, make sure the back cover is completely closed. Also, check if the tape cartridge is empty and replace it if needed. Finally, if there is a tape jam, remove the cartridge, gently pull out the jammed tape, cut off any excess with scissors, and carefully reinsert the cartridge.
How to fix blurred printing on Casio Label Maker?
Blurred, blotched, or broken printing on your Casio Label Maker can be caused by several factors. First, adjust the print density setting. Second, improper cartridge loading can be the cause, so remove and correctly reload the tape cartridge. Lastly, a dirty print head or rubber roller can cause this issue; clean the printer head and roller.
Why is the text cut off on my Casio KL-100E?
If the printed text is being cut off by the tape cut operation on your Casio Label Maker, ensure that the printer is not set up for manual tape feed. Press the FEED key before cutting the tape. Also, check if you are out of tape and replace the tape cartridge with a new one if needed.
Why does my Casio KL-100E print blank tape?
If the tape comes out when you press PRINT on your Casio Label Maker, but nothing is printed, it's likely that only blank spaces were input. Input the text you want to print.
Why won't my Casio Label Maker labels stick?
If your Casio Label Maker label won't stick, make sure you've removed the backing paper to expose the adhesive. Also, labels don't adhere well to rough, wet, oily, or dirty surfaces.
What to do if ink ribbon is fed with tape on Casio Label Maker?
If the ink ribbon is being fed from the tape outlet along with the tape on your Casio Label Maker, it's likely that the ink ribbon cassette was loaded while the ink ribbon was slack. Remove the ink ribbon cassette and check to make sure the ink ribbon is not broken. Next, take up any slack in the ink ribbon and then reload the tape cartridge.
How to fix cannot input text on Casio KL-100E?
If you cannot input text on your Casio Label Maker, it's possible that the FUNC key has been pressed. Press ESC to clear FUNC key operation.
What to do if Casio KL-100E cannot cut tape?
If you cannot cut the tape on your Casio Label Maker, the tape cutter blade may be dull. Take the label printer to the dealer from whom you purchased it to have the tape cutter blade replaced.
What does ERR! mean on my Casio Label Maker?
This error on the Casio Label Maker screen can appear for several reasons. It may be due to attempting to input two B marks within the same text or attempting to input a B mark while 6mm is specified as the tape width. Also, this can be caused by label text containing a B mark was input and then tape width specification was changed to 6mm. This error can also appear when the text is longer than 5.5cm when stamp printing is selected, attempting to print a stamp while 6mm is specified for the tape width, or inputting an incorrect value while using the currency conversion functions. Use only one B mark, don't use B marks when 6mm tape is selected, delete the B mark to print on 6mm tape or switch back to a wider tape, shorten the text for stamp printing, change the tape width setting to OFF to...
Advises on using the correct power source and avoiding overloaded outlets to prevent fire and electrical shock.
Instructs on immediate actions for smoke/odors to prevent electrical shock.
Provides precautions for using the AC adaptor to prevent fire and electrical shock.
Warns against disassembling, unstable placement, dropping, and touching the tape cutter.
Covers safe battery use, preventing leaks, mixing types, and storage.
Advises on environmental conditions, avoiding liquids, foreign objects, and unit disassembly for safe operation.
Details the two power supply methods: six AA-size batteries or an optional AC adaptor.
Explains the low battery indicator, data loss upon battery change, and safe battery handling practices.
Provides step-by-step instructions for safely loading AA alkaline batteries into the printer.
Lists printing precautions and the basic steps for printing a tape.
Details the process of printing input text onto a tape and cutting it to size.
Details how to input and set the exchange rate for currency calculations.
Outlines the steps to perform a currency conversion and print the result on a label.
Provides instructions for cleaning the printer head and roller to improve print quality.
Addresses issues with text input and tape not feeding correctly during printing.
Covers problems with print quality (blurred, blotched) and tape cutting.
Details possible causes and actions for the ERR! message, including tape width and input limits.
General| Keyboard | QWERTY |
|---|---|
| Print Method | Thermal transfer |
| Display | LCD |
| Tape Width | 6, 9, 12 mm |
| Power Supply | AC adapter |
| Character Styles | Normal, Bold, Outline, Shadow |
| Label Width | 6, 9, 12 mm |
To Next Page
