Castelgarden 122 Series

Questions and Answers

R
Rebecca TurnerAug 19, 2025
What to do if my Castelgarden Lawn Mower engine starts but does not run?
- J
  John HansonSep 12, 2025
  If your Castelgarden Lawn Mower's engine starts but won't run, there could be several reasons. First, the battery may be insufficiently charged, so recharge it. Second, there might be a faulty fuel supply, so check the level in the tank. Also, open the fuel stopcock, and check the fuel filter. Finally, check for faulty ignition, ensuring the spark plug cap is securely fitted and the electrodes are clean with the correct gap.
L
Latasha HicksAug 21, 2025
Why my Castelgarden Lawn Mower dashboard fails to switch on?
- H
  hughesmaryAug 21, 2025
  If your Castelgarden Lawn Mower's dashboard fails to switch on and there is no acoustic signal, it could be due to a badly connected or inverted battery, so check the connections. The battery might also be completely discharged, requiring a recharge. Another possibility is a blown fuse, which would need replacement (10 A). Lastly, a wet circuit board could be the issue; dry it using lukewarm air.
V
Vincent MarshallAug 23, 2025
What to do if my Castelgarden Lawn Mower is difficult to start or runs erratically?
- P
  Pamela WardAug 25, 2025
  If you're finding it difficult to start your Castelgarden Lawn Mower, or if the engine runs erratically, it could be due to carburation problems. Try cleaning or replacing the air filter. You can also empty the fuel tank and refill it with fresh fuel and check and replace the fuel filter if necessary.
J
Jennifer HowardAug 26, 2025
Why Castelgarden Lawn Mower engine stops running and generates acoustic signal?
- J
  Jason BlairAug 26, 2025
  If your Castelgarden Lawn Mower engine stops and an acoustic signal sounds, it might be due to over-voltage caused by the charger regulator, in this case contact your Dealer. Alternatively, the battery might not be connected correctly (poor contacts) or it could be disconnected. In both cases, check the connections.
D
Dr. Michael RichardsonAug 27, 2025
What to do if Castelgarden Lawn Mower has unusual vibrations while working?
- M
  Melissa BirdAug 28, 2025
  If your Castelgarden Lawn Mower experiences unusual vibrations while working, it could be because the cutting means assembly is full of grass. Clean the cutting means assembly. Also, check and tighten all the engine and frame bolts, as loose bolts and screws can cause vibrations.
A
Anne FryAug 30, 2025
Why is my Castelgarden Lawn Mower mowing unevenly with insufficient collection?
- J
  Joseph SotoAug 30, 2025
  Uneven mowing and insufficient collection in your Castelgarden Lawn Mower could stem from several causes. Check the tyre pressure, as the cutting means assembly might not be parallel to the ground. Reduce the forward speed and/or raise the cutting device assembly if the forward speed is too high compared to height of grass. Also, ensure the collector chute is not blocked by removing the grass catcher and emptying the chute. If the cutting means are inefficient, contact your Dealer. Reinstate the alignment of the cutting means assembly in relation to the ground. Finally, wait for the grass to dry.
D
Danielle HudsonSep 1, 2025
Why is my Castelgarden Lawn Mower mowing unevenly?
- P
  patriciaperezSep 1, 2025
  Uneven mowing with your Castelgarden Lawn Mower (side discharge models) can occur if the cutting means assembly is not parallel to the ground, so check the tyre pressure. You may also need to reinstate the alignment of the cutting means assembly in relation to the ground. If the cutting means are inefficient, contact your Dealer.
M
melinda58Sep 3, 2025
What to do if Castelgarden Lawn Mower cutting device do not engage or stop?
- M
  matthew71Sep 3, 2025
  If the cutting device on your Castelgarden Lawn Mower doesn't engage or stop properly, it might be due to a loose belt or problems with the electro-magnetic clutch, in this case contact your Dealer.
F
feliciagutierrezSep 5, 2025
Why Castelgarden Lawn Mower dashboard fails to switch on but acoustic signal is activated?
- G
  goconnorSep 5, 2025
  If the dashboard on your Castelgarden Lawn Mower fails to switch on, but the acoustic signal is activated, the circuit board may be wet. Try drying it using lukewarm air.
P
Patricia KellySep 7, 2025
What to do if Castelgarden Lawn Mower remains stationary when the drive pedal is pressed?
- M
  Mr. Jeffrey MunozSep 7, 2025
  If your Castelgarden Lawn Mower remains stationary even when the drive pedal is pressed while the engine is running, check if the release lever is in the gear disengagement position. If so, return it to the gear engaged position.