What to do if I get 'Alert / The backup has failed' on CC-ISOBUS CCI 1200 Touch terminals?
If you receive an 'Alert / The backup has failed' message on your CC-ISOBUS Touch terminals, ensure that: * A flash drive is connected to the terminal. * The flash drive is functioning correctly. * The write-protection switch of the flash drive is in the "off" position. * The flash drive has at least 1GB of free storage.
What to do if the connected implement is not displayed on CC-ISOBUS CCI 1200 Touch terminals?
If a connected implement isn't showing up on your CC-ISOBUS Touch terminal, there are a few potential causes: * The implement might not be correctly connected. Ensure the implement’s ISOBUS cable is securely connected to the tractor. * A bus terminator might be necessary. Check if the implement requires a bus terminator. * The UT configuration could be incorrect. Configure the UT of the terminal according to the manual.
How to fix incorrect network password on CC-ISOBUS CCI 1200?
If you're getting an 'Incorrect network password' error on your CC-ISOBUS Touch terminals, it means you've likely entered the wrong WiFi password. To correct this, press and hold the button with the WiFi network name in the selection list for two seconds. Then, select 'Edit', enter the correct password, and confirm with 'OK'.
What does 'Caution / The terminal is not connected with the ISOBUS' mean on CC-ISOBUS Touch terminals?
If you see the message 'Caution / The terminal is not connected with the ISOBUS' on your CC-ISOBUS Touch terminals, restart the terminal, disconnect the implement from the ISOBUS, wait 5 seconds, and then reconnect the implement to the ISOBUS.
What to do if I get 'Alert / No flash drive connected' on CC-ISOBUS CCI 1200 Touch terminals?
If you receive an 'Alert / No flash drive connected' message on your CC-ISOBUS Touch terminals, ensure that: * The flash drive is connected to the terminal. * The flash drive is functioning correctly. * The write-protection switch of the flash drive is in the "off" position. * The flash drive has at least 10MB of free storage.
What to do if I get 'Alert / The shape file could not be exported' on CC-ISOBUS CCI 1200 Touch terminals?
If you receive an 'Alert / The shape file could not be exported' message on your CC-ISOBUS Touch terminals, repeat the process and leave the flash drive plugged in until the process has completed.
What to do if CC-ISOBUS CCI 1200 Touch terminals are not connected with the ISOBUS?
If the CC-ISOBUS Touch terminal is not connected to the ISOBUS, try restarting the terminal. Alternatively, disconnect the implement from the ISOBUS, wait 5 seconds, and then reconnect it.
What to do if the selected UT number is already being used on CC-ISOBUS CCI 1200 Touch terminals?
If the selected UT number is already being used on your CC-ISOBUS Touch terminal, please select another UT number and restart the terminal.
What to do if I get 'Alert / The report could not be exported' on CC-ISOBUS Touch terminals?
If you receive an 'Alert / The report could not be exported' message on your CC-ISOBUS Touch terminals, repeat the process and leave the flash drive plugged in until the process has completed.
What to do if shape file could not be exported on CC-ISOBUS CCI 1200 Touch terminals?
If the shape file could not be exported from your CC-ISOBUS Touch terminals, it might be because you removed the flash drive before the action was completed. Repeat the process, making sure to leave the flash drive plugged in until the export is complete.
Explains how warning notes, cautions, and informational notes are identified and used in the manual.
Defines the exclusive intended use of the terminal in agriculture and manufacturer liability.
Provides essential safety instructions for operation, handling, and maintenance to prevent hazards.
Addresses safety considerations for installing electrical and electronic devices to avoid interference and hazards.
Details tractor data availability via ISOBUS/signal connector and guides on setting up tractor parameters.
Guides on adding, selecting, and configuring implements, including working width, type, and mounting.
Covers setting up the GPS receiver, including position and interface selection for accurate data.
Introduces the map view for Section Control and Rate Control, explaining its automatic section switching feature.
Provides guidance on behavior during technical failures, stopping work, finding solutions, and forced shutdown.
Lists common operational problems, their causes/remedies, and guides on capturing screenshots.
General| Display Size | 12.1 inch |
|---|---|
| Resolution | 1280 x 800 pixels |
| Touchscreen | Yes |
| Operating Temperature | -20°C to +60°C |
| ISOBUS Compatibility | Yes |
| Touch Technology | Capacitive |
| Processor | ARM Cortex-A9 |
| Operating System | Linux |
| RAM | 1 GB |
| Internal Storage | 8 GB |
| Protection Class | IP 65 |
| Connectivity | Ethernet, USB |
| IP Rating | IP67 |
To Next Page
