CCL BAS-G - Page 17

Date: DD/MM/YY
Time: HH:MM in 24 Hours format
Tel: X (X= no of Tel Numbers stored)
Wired Zones Active: X (No of Wired Zones
that are Enabled out of 8 Wired Zones)
Wireless Sensor: X (No of Wireless Sensors
Registered, except Remotes)
Remote: X (No of Remotes registered)
5
System details – Detailed
XXXX+SYS DETAIL
System will send SMS giving following details:
System Status: ARMED or DISARMED
Power: On Mains / On Battery
W STAT: This shows the Modes in which 8
Wired Zones are Enabled. DS
means Disabled. NA= Normal ARM,
AA= Always ARM, TR= Traitor, BA=
By Pass,
WL Stat: This shows the ID, Type and Mode
of the registered wireless sensors.
MS= Magnetic Switch, VIBR=
Vibration Sensor, RMT= Remote,
PIR= Motion Sensor, TAMP=
Tamper Sensor, PAN= Panic,
HEAT= Heat Detector, SMK=
Smoke Detector, GAS = GAS
Detector, HHW= Heat and Humidity
Detector, BEAM= Beam Sensor,
WKBD= Wireless Key Board, M+S=
Magnetic Sensor with Switch
DS means Registered but Disabled.
NA= Normal ARM, AA= Always
ARM, TR= Traitor, BA=By Pass.
6
Registered telephone
number list
XXXX+TEL
All the registered Telephone numbers will be
listed.
7
Change Master Password
CHANGE PW XXXX YYYY
XXXX = old Master Password , YYYY = New Master
Password
8
SIM balance check
SIMBAL ccccc
ccccc = Service provider’s SIM balance code. E.g. for
Airtel , it is *123#. You will get a SMS stating the
balance in SIM of BAS.
9
Add telephone number
XXXX+ATELjk ttttttttt
j = Tel location from 1-6 , k = E for SMS commands
enable/ D for SMS commands disable , tttttttt =
telephone number (max 11 digits)
10
Delete telephone number
XXXX+DTELj
j = tel location from 1 – 6
11
Set auto Arm/Disarm
XXXX+AUTOj aaaa dddd
j = group number (1 -3) , aaaa = arm time in 24hr
format , dddd= disarm time in 24hr format. This
setting will be applied for all the 7 days of the week.
12
Disable auto Arm/Disarm
XXXX+OFFAUTO
Auto ARM/DISARM will be disabled.
13
Delete all wireless sensors
XXXX+WLALLDEL
All Wireless Sensors will be deleted.
14
Delete specific wireless
sensor
XXXX+WLDEL nn
nn= wireless ID to delete.
15
Add wireless sensor
XXXX+WLADD nn y
nn=wireless ID, y = type of sensor. Refer table below
for values.
16
Change mode of specific
wireless sensor
XXXX+WLMOD nn y
nn = wireless ID , y = mode of sensor( 0=Normal Arm
, 1 = Disable, 2= arm bypass , 3 = always armed)
17
Disable all wired zones
XXXX+WRALLDIS
All Wired Zones will be disabled.
18
Set mode of specific wired
zone
XXXX+WRMOD n y
n = wired zone (1 to 8), y = mode of zone ( 0=Normal
Arm , 1 = Disable, 2= arm bypass , 3 = traitor mode, 4
= always armed)
19
Set name of wired zone
XXXX+WNAMEn pppp
n = wired zone (1 to 8), p= name of wired zone (up to
15 characters). This name will be used in SMS sent to
users & CMS.
20
Set name of first eight
wireless sensor
XXXX+WLNAMEn pppp
n = wireless sensor (1 to 8), p= name of wireless
sensor (up to 15 characters). This name will be used
in SMS sent to users & CMS.