EasyManua.ls Logo

Central Pneumatic 60801 - Maintenance

Central Pneumatic 60801
16 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
Page 14 ;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1 Item 60801
EF;6GH IJ6KFGLIM NFLMG6MFMO6E6GPJ
P#*(?N,"8$*8,84*%L8#$('4$"&8#
%J(&4*9'(*#%8&$%#/*4"2"4,77[%*\/7,"8*9%"8%$."#%5,8',7%5'#$%
+*%/*(2&(5*9%&87[%+[%,%<',7"2"*9%$*4.8"4",81
GI%JK6!6MG%E6KLIPE%LMXPKH%;KIN%FOOLU6MGFT%IJ6KFGLIM-%
G'(8%&22%$.*%E&9,%S7,#$*(=%9*$,4.%$.*%,"(%#'//7[=%#,2*7[%9"#4.,(3*%,8[%(*#"9',7%,"(%/(*##'(*%
"8%$.*%E&9,%S7,#$*(=%,89%(*7*,#*%$.*%$.(&$$7*%,890&(%$'(8%$.*%],7]*%$&%"$#%&22%/&#"$"&8%
+*2&(*%/*(2&(5"83%,8[%"8#/*4$"&8=%5,"8$*8,84*=%&(%47*,8"83%/(&4*9'(*#1
GI%JK6!6MG%E6KLIPE%LMXPKH%;KIN%EIUF%STFEG6K%;FLTPK6-%
U&%8&$%'#*%9,5,3*9%*<'"/5*8$1%%L2%,+8&(5,7%8&"#*=%]"+(,$"&8=%
&(%7*,Y"83%,"(%&44'(#=%.,]*%$.*%/(&+7*5%4&((*4$*9%+*2&(*%2'($.*(%'#*1
O7*,8"83%,89%N,"8$*8,84*
M&$*- These procedures are in addition to the regular checks and maintenance
explained as part of the regular operation of the air-operated Soda Blaster.
1. S6;IK6%6FOW%PE6= inspect the general
condition of the Soda Blaster. Check for:
loose hardware or housing,
misalignment or binding of moving parts,
cracked or broken parts, and
any other condition that may
affect its safe operation.
2. U,"7[%?%F"(%E'//7[%N,"8$*8,84*-%
Every day, maintain the air supply according
to the component manufacturers' instructions.
Drain the moisture filter regularly.
Performing routine air supply maintenance will
allow the Soda Blaster to operate more safely
and will also reduce wear on the Soda Blaster.
3. Empty the Tank, and clean external surfaces
of the Soda Blaster with clean, dry cloth.
G(&'+7*#.&&$"83
1. Excess moisture will cause the abrasive to slow
or stop flowing through the Abrasive Outlet Pipe.
To test, check the abrasive by pouring a 6″ cone
of abrasive on dry newspaper. After several
minutes, remove the abrasive from the newspaper.
Do not use the abrasive if the newspaper is moist.
2. Poor or irregular flow of the abrasive may also be due
to low air pressure or a worn Nozzle.
To correct, increase the air pressure
(to no more than 90 PSI) and/
or replace the worn Nozzle.
K*4&(9%J(&9'4$f#%E*(",7%M'5+*(%W*(*-%
M&$*- If product has no serial number, record month and year of purchase instead.
M&$*- Some parts are listed and shown for illustration purposes only, and are not available
individually as replacement parts. Specify UPC 193175328892 when ordering parts.

Related product manuals