Central Pneumatic 64142 - Page 15

Page 15?*,)(.82<&80;)@+.'(&*<'A)3;.0'.)80;;)#BCCCBC!!BDEFE5Item 64142
GH?:IJKL:MHINKOPHNOI:OHOQ: G:IRL
R'.,BP0&<(.<0<8.)N<'(,+8(&*<'
)L,*8.=+,.')<*()'3.8&6&80;;X).^3;0&<.=)&<)(2&')90<+0;)9+'()/.)3.,6*,9.=)*<;X)/X)0)@+0;&6&.=)(.82<&8&0<5
IK)LM:%:OI)G:MNKRG)NO[RMJ)?MKP)HQQNW:OIHV)WNGQZHMT:A))
U:?KM:)HOJ)PHNOI:OHOQ:)KM)M:LHNMG)HM:)WKO:)g&<8;+=&<7)8;.0,&<7)]09'h1
i)S.0,)HOGNB033,*_.=)'06.(X)7*77;.')-&(2)'&=.)'2&.;='5)))
Other people in the work area must also wear ANSI-approved impact safety goggles with side shields.
i)M.;.0'.)(2.)I,&77.,5
i)W.(082)(2.)0&,)'+33;X5
i)H((.93()(*)=&'820,7.)(2.)I**;)&<(*)0)3&.8.)*6)'8,03)-**=)(*).<'+,.)(20()
&()&')=&'8*<<.8(.=)0<=)&')&<8030/;.)*6)=,&_&<7)0<X)60'(.<.,'5
i):93(X)(2.)P070b&<.)0<=);.0_.)&()*3.<)=+,&<7)'.,_&8.5)))
I2.)P070b&<.)&')'3,&<7B;*0=.=)0<=)90X)80+'.)30,(')*,)0)60'(.<.,)(*)6;X)*+()*6)(2.)I**;5
IK)LM:%:OI)G:MNKRG)NO[RMJ)?MKP)IKKV)?HNVRM:1)
W*)<*()+'.)=0907.=).@+&39.<(5)))
N6)0/<*,90;)<*&'.A)_&/,0(&*<A)*,);.0\&<7)0&,)&')=.(.8(.=A)20_.)(2.)3,*/;.9)8*,,.8(.=)/.6*,.)6+,(2.,)+'.5
IK)LM:%:OI):eLVKGNKO1))V+/,&80(.)*<;X)-&(2)'3.8&6&.=);+/,&80<('5))V+/,&80(.)(2.)0&,)&<;.()
+'&<7)*<;X)3<.+90(&8)(**;)*&;5))V+/,&80(.)(2.)&<(.,<0;)9.820<&'9)+'&<7)*<;X)-2&(.);&(2&+9)
7,.0'.5))K(2.,);+/,&80<(')90X)=0907.)(2.)9.820<&'9)0<=)90X)/.)2&72;X)6;0990/;.A)80+'&<7)
0<).^3;*'&*<5
O*(.1 These procedures are in addition to the regular checks and maintenance
explained as part of the regular operation of the air-operated Tool.
1. U:?KM:):HQZ)RG:A inspect the general
condition of the Tool. Check for:
• proper safety trip mechanism operation,
• free Workpiece Contact and Trigger movement,
• loose hardware or housing,
• misalignment or binding of moving parts,
• cracked or broken parts, and
• any other condition that may
affect its safe operation.
2. W0&;X)B)H&,)G+33;X)P0&<(.<0<8.1)
Every day, perform maintenance on the air supply
according to the component manufacturers'
instructions. Maintain the lubricator's oil level.
Drain the moisture filter regularly.
Performing routine maintenance on the air
supply will allow the Tool to operate more
safely and will also reduce wear on the Tool.