Central Pneumatic 64142 - Operation

Page 12 ?*,)(.82<&80;)@+.'(&*<'A)3;.0'.)80;;)#BCCCBC!!BDEFE5 Item 64142
GH?:IJ KL:MHINKO PHNOI:OHOQ:G:IRL
Q*<(08()H8(+0(&*<)P.820<&'9)W.6&<&(&*<
The contact actuation mechanism allows rapid placement of fasteners. Use the switch near the trigger to
change modes. The Tool should only actuate if the Workpiece Contact is pressed against the workpiece
and the Trigger is pulled. It should actuate again if the Trigger is released and pulled OR if the Workpiece
Contact is lifted and pressed against the workpiece again. The Tool should not actuate if the Workpiece
Contact is not pressed against an object. Q*<(08()H8(+0(&*<)'2*+;=)*<;X)/.).<0/;.=)0<=)+'.=)
/X)'\&;;.=)*3.,0(*,')-2*)0,.)0-0,.)*6)(2.)20b0,=')0<=)+'.)3,*3.,A)'06.)-*,\)3,08(&8.'5
Q*<(08()H8(+0(&*<)P.820<&'9)I.'(&<7)L,*8.=+,.
IK)LM:%:OI)G:MNKRG)NO[RMJ)?MKP)HQQNW:OIHV)WNGQZHMT:1)
L*&<()(2.)(**;)0()0)3&.8.)*6)'8,03)-**=)-2.<)(.'(&<75
1. Disconnect the Tool from the air supply.
2. Load the magazine with fasteners.
3. Check that the Trigger and the Workpiece
Contact move freely, without sticking.
4. Connect the air supply to the Tool and
set within the Operating Air Pressure
indicated on the Specification chart.
5. Test the Tool by pressing the Workpiece Contact
against the workpiece without pulling the Trigger.
I2.)I**;)9+'()<*()8X8;.)g08(+0(.h5
If it cycles (actuates), stop immediately and have
it repaired by a qualified service technician.
6. Hold the Tool away, or off of the workpiece.
The Workpiece Contact should return to its original
position. Squeeze the Trigger.
I2.)I**;)9+'()<*()8X8;.)g08(+0(.h5
If it cycles (actuates), stop immediately and take
the Tool to a qualified service technician.
7. Press the Workpiece Contact against the workpiece
and squeeze the Trigger.
I2.)I**;)9+'()8X8;.)g08(+0(.h)*<;X)*<8.5
Release the Trigger, slide the Tool to a fresh piece of
wood, and squeeze it again.
I2.)I**;)9+'()8X8;.)g08(+0(.h)070&<)*<;X)*<8.5
With the Trigger depressed, carefully lift the Tool
and press it against the workpiece again in a new
location.
I2.)I**;)9+'()8X8;.)g08(+0(.h)070&<)*<;X)*<8.5
If it fails to act in the manner explained in bold,
have it repaired by a qualified service technician.
G-&(820/;.)I,&77.,
IK)LM:%:OI)G:MNKRG)NO[RMJ)?MKP)HQQNW:OIHV)WMN%NOT1
i)M.;.0'.)I,&77.,)0<=)3*&<()I**;)&<)0)'06.)=&,.8(&*<)/.6*,.)820<7&<7)08(+0(&*<)9*=.5
i)KOVJ)*3.,0(.)(2.)I**;)-&(2)(2.)P*=.)G-&(82)6+;;X)&<)*<.)*6)(2.)08(+0(&*<)9*=.)3*'&(&*<'5
1. Turn the Mode Switch to the (single nail)
setting to enable G&<7;.)G.@+.<(&0; operation
for precise placement of fasteners.
2. Turn the Mode Switch to the (multiple
nail) setting to enable 8*<(08()08(+0(&*<
operation for rapid placement of fasteners.
K<;X)0)'\&;;.=)*3.,0(*,)-2*)&')0-0,.)*6)
(2.)20b0,=')0<=)+'.')3,*3.,A)'06.)-*,\)
3,08(&8.')'2*+;=)+'.)8*<(08()08(+0(&*<)
*3.,0(&*<5
G&<7;.)G.@+.<(&0;)
L*'&(&*<
Q*<(08()H8(+0(&*<)
L*'&(&*<
?&7+,.)Q1))I,&77.,)P*=.)G-&(82)L*'&(&*<'