Chamberlain K1D8389-1CC User Manual


#ONTROL "OARD 2EPLACEMENT
-ODEL +$##
4O REDUCE THE RISK OF ).*529 OR $%!4(
z $ISCONNECT ALL POWER "%&/2% INSTALLING OR SERVICING OPERATOR
z 3EE MANUAL PRIOR TO SERVICING REGARDING MAINTENANCE AND REQUIRED SAFETY TESTING
7!2.).' 4HIS PRODUCT CAN EXPOSE YOU TO CHEMICALS INCLUDING LEAD WHICH ARE KNOWN TO THE 3TATE OF #ALIFORNIA TO CAUSE CANCER OR BIRTH DEFECTS
OR OTHER REPRODUCTIVE HARM &OR MORE INFORMATION GO TO WWW07ARNINGSCAGOV
)NTRODUCTION
4HIS KIT PROVIDES A REPLACEMENT CONTROL BOARD FOR ALL ,IFT-ASTER $# GATE OPERATORS 3LIDE GATE OPERATORS WITH THE NEW CONTROL BOARD REQUIRE A MINIMUM OF
TWO EXTERNAL MONITORED ENTRAPMENT PROTECTION DEVICES TO FUNCTION ONE IN THE OPEN DIRECTION AND ONE IN THE CLOSE DIRECTION 3EE 6ERIFY 0ROPER %NTRAPMENT
0ROTECTION SECTION
2EPLACE THE #ONTROL "OARD
 2EMOVE THE OPERATOR COVER OR ELECTRICAL BOX COVER TO ACCESS THE CONTROL BOARD
 $ISCONNECT ALL WIRING FROM THE CONTROL BOARD AND LABEL THE LOCATION FOR REWIRING TO THE NEW CONTROL BOARD
 2EMOVE THE CONTROL BOARD FROM THE OPERATOR
 )NSTALL THE NEW CONTROL BOARD
 2ECONNECT ALL WIRING TO THE NEW CONTROL BOARD SEE #ONTROL "OARD /VERVIEW SECTION
0ROCEED TO THE FOLLOWING SECTIONS TO COMPLETE ADJUSTMENT AND SETUP OF THE OPERATOR

Chamberlain K1D8389-1CC Specifications

General

Type	Swing Gate Opener
Voltage	24V DC
Compatibility	Swing gates
Security	Rolling code technology
Motor Type	DC
Maximum Gate Weight	850 lbs
Control Options	Remote control, keypad
Safety Features	Obstacle detection

Summary

Introduction

Replace the Control Board

Steps to replace the control board in the gate operator.

Control Board Overview

Control Buttons and Operation

Covers SET OPEN/CLOSE, MOVE GATE, and TEST buttons for gate control and setup.

Adjustment Dials and Switches

Dials and switches for force, timer, delay, and backdrive settings.

Status Indicators and Diagnostics

LEDs and display for monitoring operator status and information.

Battery Fail Function

Details the operator's behavior during power loss and low battery.

Verify Proper Entrapment Protection

Entrapment Zone Definitions

Definitions of entrapment zones for different gate types.

Wire Entrapment Protection Devices

Close Eyes/Interrupt Wiring

Wiring for photoelectric sensor entrapment protection in the close direction.

Close Edge Wiring

Wiring for edge sensor entrapment protection in the close direction.

Open Eyes/Edge Wiring

Wiring for sensor or edge entrapment protection in the open direction.

Dual Gate Setup

Wireless Setup

Instructions for setting up wireless communication between dual gates.

Deactivating Wireless Feature

Steps to disable wireless communication between dual gates.

Limit and Force Adjustment

Introduction to Limit and Force

Explains operator design for easy limit and force adjustments.

Initial Limit and Force Adjustment

Steps for setting initial gate travel limits and force.

Fine Tune the Force

Adjust the Limits

Obstruction Test

Programming Remote Controls

Single Button Open Only

Program one remote button for opening the gate.

Single Button Open, Close, Stop

Program one remote button for open, close, and stop functions.

Three Button Open, Close, Stop

Program three remote buttons for open, close, and stop functions.

LiftMaster Internet Gateway Setup

Gateway Programming Methods

Instructions for programming the internet gateway using operator buttons.

Managing Codes and Limits

Procedures for erasing all remote codes and gate travel limits.

Constant Pressure Override (CPO)

How to use CPO to temporarily bypass entrapment protection.

Reinstalling the Operator Cover

Instructions for replacing the operator's cover after maintenance.