EasyManua.ls Logo

Chicago Electric 66508 - User Manual

Chicago Electric 66508
18 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
50 FT. DRAIN CLEANER
WITH POWER FEED
66508
ASSEMBLY AND OPERATING INSTRUCTIONS
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright
©
2008 by Harbor Freight Tools
®
. All rights reserved. No portion of this manual or any artwork contained
herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may
differ slightly from the product described herein. Tools required for assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Revised Manual 09b, 09k

Table of Contents

Questions and Answers

  • T
    Timothy RobertsAug 1, 2025
    What to do if the Chicago Electric Power Tool's power cord GFCI trips?
    • R
      reidjosephAug 1, 2025
      If the GFCI trips when the unit is plugged in or the foot pedal is pressed, there are several potential causes: * A defective Motor Direction Switch. * A frayed Power Cord. * A short circuit in the Motor. * Excess moisture touching the Power Cord or Drain Cleaner. * A faulty GFCI unit. Suggested solutions include repairing or replacing the Motor Direction Switch or Power Cord, having the motor repaired or replaced by a qualified technician, removing any moisture, or replacing the Power Cord with GFCI.
  • R
    Robert HallAug 6, 2025
    Why does the Chicago Electric Power Tool cable kink, twist, or break?
    • D
      dixoncassidyAug 7, 2025
      The cable may kink, twist, or break due to: 1. Applying too much force on the cable; let the cutter tool do the work, and don't force the cable. 2. Having too much slack between the Drain Cleaner and the drainpipe inlet; move the Drain Cleaner to within two feet of the drainpipe inlet. 3. Using the wrong size cable for the drain pipe; change the cable size. 4. Exposing the cable to acid; clean and oil the cable regularly. 5. The cable being worn out; replace the cable.
  • S
    schultzbethAug 13, 2025
    What to do if Chicago Electric Power Tool cable does not feed when the Foot Pedal is pressed?
    • K
      Kayla DavisAug 13, 2025
      If the cable does not feed when the Foot Pedal is pressed, it could be due to: 1. The cable being tangled in the Drum; do not run the Motor in reverse, unplug the Drain Cleaner and manually pull the cable out until the tangle is cleared. 2. Incorrect feed tension; adjust the feed tension Star Knob (44-13). If the Knob is too loose, the cable will slip, and if it's too tight, the rollers will wear prematurely. 3. A frozen feed roller; clean and lubricate the feed rollers, and replace worn rollers. 4. The cable being worn out; when the cable coils wear flat, it should be replaced.
  • S
    Sheri GouldAug 19, 2025
    What to do if Chicago Electric Power Tool motor cuts off during use?
    • T
      Timothy MillsAug 20, 2025
      The motor may have been shut off by its internal thermal protection switch or auto reset breaker. To resolve this, turn the motor off, allow it to cool off completely before restarting, and stay clear of the cable when turning the motor back on.
  • T
    Tami HawkinsAug 25, 2025
    Why does the Chicago Electric Power Tool cable tangle in the drum?
    • A
      Angel MorganAug 25, 2025
      The cable may tangle in the drum due to: 1. Applying too much force on the cable; do not force the cable, let the cutter tool do the work. 2. The motor running in reverse; retract the Cable with the Motor Direction Switch (5) in the Forward position. 3. The distributor tube being frozen; lubricate the distributor tube bearings.

Summary

General Safety Rules

Work Area Safety

Electrical Safety

Protect against electric shock by avoiding grounded surfaces and moisture.

Personal Safety Precautions

Stay alert, dress appropriately, and take measures to prevent accidental starts.

Specific Safety Rules for this Product

Product-Specific Safety Guidelines

Follow critical safety rules tailored for the drain cleaner's operation and environment.

Grounding and Electrical Protection

Grounding Requirements and Connection

Ensure correct grounding wire connection to prevent electric shock.

Ground Fault Circuit Interrupter (GFCI)

Understand GFCI operation, testing, and importance for shock protection.

Extension Cord Safety

Operating Instructions

Operational Components and Controls

Selecting and Attaching Cutting Tools

Drain Cleaning Procedure

Step-by-Step Operation

Follow the detailed steps for placing the cleaner, feeding cable, and cleaning drains.

Troubleshooting Common Issues

Problem Diagnosis and Solutions

Resolve common operational problems like motor issues, cable kinks, or tangles.

Inspection, Maintenance, and Cleaning

General Inspection and Cleaning

Tangled Cable Management

Removing a Stuck Cable

Chicago Electric 66508 Specifications

General IconGeneral
Model66508
BrandChicago Electric
TypeAngle Grinder
Voltage120V
Disc Diameter4-1/2 inches
Speed11, 000 RPM
Spindle LockYes
No Load Speed11, 000 RPM
Spindle Thread5/8 inch - 11 UNC
Switch TypeSlide

Related product manuals