Chicago Electric 98265 User Manual (English)

Other manuals for Chicago Electric 98265

Set Up And Operating Instructions21 pages

Questions and Answers:

T
Timothy WarnerAug 14, 2025
What to do if my Chicago Electric Saw won't start?
- D
  Daniel OlsonAug 14, 2025
  If your Chicago Electric Saw won't start, there are several things you can check: * Ensure the cord is properly plugged in. * Verify the power at the outlet. If there's no power, turn off the saw and check the circuit breaker. If the breaker is tripped, ensure the circuit has the correct capacity for the saw and isn't overloaded with other devices. * Turn off the saw and let it cool down. Then, press the reset button on the tool. If these steps don't resolve the issue, have a technician service the saw.
T
timothy69Aug 17, 2025
What to do if the blade spins slowly on my Chicago Electric 98265 Saw?
- V
  Victor HolmesAug 18, 2025
  If the blade on your Chicago Electric Saw is spinning slowly, it could be due to: * Arbor shaft binding. Check the shaft to ensure it spins freely. * Worn motor brushes. Replace the brushes.
V
Victoria KingAug 21, 2025
Why is my Chicago Electric 98265 Saw overheating?
- K
  Kimberly KeithAug 21, 2025
  If your Chicago Electric Saw is overheating, consider the following: * Check the connection. * If applicable, add the proper amount of water and always run the saw with cold water. * Allow the machine to work at its own pace. * Check and correct the alignment of the accessory to the fence and/or table. * Keep cutting accessories sharp, replacing them as needed. * Wear ANSI-approved safety goggles and a NIOSH-approved dust mask/respirator while blowing dust out of the motor using compressed air. * Avoid using an extension cord. If one is necessary, use a cord with the correct diameter for its length and the load it's carrying.
A
Anthony ParkerAug 25, 2025
Why is my Chicago Electric Saw operating slowly?
- D
  dmackAug 25, 2025
  If your Chicago Electric Saw is operating slowly, here are some possible solutions: * First, try eliminating the use of an extension cord. If you must use one, make sure it has the correct diameter for its length and the load. * Also, check that the shaft spins freely. If the issue persists, have a technician service the tool.
A
Aaron MorganAug 27, 2025
How to reduce excessive vibration in my Chicago Electric 98265?
- D
  Diana CortezAug 28, 2025
  Excessive vibration in your Chicago Electric Saw can be due to: * A bent or off-balance blade. Replace the blade with a new one. * A bent arbor shaft. Check the shaft for run-out.
T
Thomas Benitez PhDAug 31, 2025
Why is the travel restricted on my Chicago Electric Saw?
- H
  haneymichaelAug 31, 2025
  Restricted travel in your Chicago Electric Saw may be caused by: * A dry or damaged holder. Try lubricating or servicing the holder components. * Bent sliding bars. Consider replacing the sliding bars.
W
William BrooksSep 3, 2025
What to do if my Chicago Electric Saw has excessive noise or rattling?
- S
  Shannon AdamsSep 3, 2025
  If your Chicago Electric Saw is making excessive noise or rattling, try these steps: * Replace the blade with a new one. * Check the shaft for run-out. If the problem continues, have a technician service the tool.
J
Joseph SmithSep 6, 2025
Why has the performance of my Chicago Electric 98265 Saw decreased over time?
- M
  Mrs. Molly Cain DDSSep 7, 2025
  If the performance of your Chicago Electric Saw has decreased over time: * Ensure you keep the cutting accessories sharp and replace them when needed. * Have a qualified technician replace the brushes.
B
Brandon SmithSep 10, 2025
What to do if my Chicago Electric 98265 Saw has restricted carriage travel?
- J
  Jessica HicksSep 12, 2025
  If the carriage travel on your Chicago Electric Saw is restricted: * Lubricate or service the Holder components. * Replace the Sliding Bars.