19
and videos saved in Baby Monitor
mode.
CAUTION: in Gallery mode, it is not
possible to see the image of the child
in real time as there is no link between
the parent unit and the child unit.
Holding down the button (11) for 2
seconds will switch off the parent unit.
A short beep will be heard when
switching the parent unit on and off in
Gallery mode.
+ - volume adjustment of the parent
unit loudspeaker
The + (5a) and – (5b) volume adjust-
ment buttons (6) adjust the volume
of sounds emitted by the child unit in
Baby Monitor mode, while in Gallery
mode, they adjust the volume of the
videos recorded.
Press + (5a) and – (5b) to adjust par-
ent unit loudspeaker (6) volume and
select the desired level.
The unit offers 10 volume setting lev-
els. The factory set level is 5.
Press the “+” button (5a) once to in-
crease the volume by one level.
Press the “-“ (5b) button once to de-
crease the volume by one level.
The change in the volume level will be
shown on the display (4)
The appliance stores the volume
level selected during previous use in
its memory, even after it has been
switched off and switched back on.
Note: The volume adjustment icon in-
cludes 5 bars: each bar lights up after
2 presses of the + (5a)/- (5b) button.
A beep will be heard each time the
volume is increased or decreased by a
level. A double beep will be heard each
time the maximum or minimum level
is reached.
Adjusting the brightness of the parent
unit display
It is possible to adjust the brightness
(4) of the parent unit display by ac-
cessing the main menu on the parent
unit in Baby Monitor mode. 7 bright-
ness levels are available.
For details about adjustment, see
paragraph 3.2.2.
Contact List Management
It is possible to compile and consult
the Contact List by accessing the main
menu on the parent unit in both Baby
Monitor and Gallery mode.
For details about contact list manage-
ment, see paragraph 3.2.5.
Parent/child unit communication
Talk function
The Talk function makes it possible
for parents to communicate with the
child when the appliance is in Baby
Monitor mode. Press and hold the
button (12) and talk near the parent
unit microphone (16). When the talk
function is on, it is not possible to hear
sounds from the child unit on the par-
ent unit.
CAUTION: when using the ‘Talk’ func-
tion, avoid talking too close to the par-
ent unit microphone (16) or the child
unit will receive very high intensity
sounds.
CAUTION: do not press the button
(12) when the two units are in the
same room or less than 3 metres apart
as this could cause noises or hissing.
Voice Activation function
In Baby Monitor mode, the parent
unit can operate in continuous trans-
mission mode or in voice activation
mode. The Voice Activation function
is activated from the internal par-
ent unit menu. When the intensity
of the sounds detected by the micro-
phone (6) on the child unit exceeds
the threshold for voice activation set
by the manufacturer, the image of
the child is shown in real time on the
display (4) and the loudspeaker (6)
on the parent unit is activated. In the
presence of sounds with intensity lev-
els below this threshold, the display
(4) stops displaying the image of the
child and the speaker (6) is turned off.
When this function is set, the
icon is shown on the display. For details
about activation, see paragraph 3.2.1.
Photo Capture and Photo Gallery
Function
Using the Capture Photo function, you
can save the best pictures of the child
when the units are linked and operat-
ing in Baby Monitor mode. To save an
image captured by the video camera
and shown on the display, press the
Capture Photo button (15): the
icon will appear on the display (4) for
a few seconds. If there is no space in
the memory on the parent unit, the
display (4) will show the message
‘FULL MEMORY’ and the photo will
not be saved.
To Next Page
Loading...
