Cisco 2600 Series - User Manual

About This Guide ix
About This Guide
This preface discusses the objectives, audience, organization, and conventions of this
network module hardware installation guide.
Objectives
This publication provides hardware installation information for Cisco network modules
used in Cisco 3600 series and Cisco 2600 series modular access routers, referred to as
Cisco modular routers.
This publication describes a variety of router models that are similar in functionality, but
differ in the number of interfaces supported. Some information provided might not apply
to your particular router model.
How to Use This Guide
This guide contains an overview of network modules and information on connecting
specific network modules to your Cisco modular router. Refer to Table 1-1 in Chapter 1,
“Overview of Cisco Network Modules” for a listing of network modules supported by
Cisco 3600 series routers and the required release of Cisco IOS software for each module.
Refer to Table 1-2 in Chapter 1, “Overview of Cisco Network Modules” for a listing of
network modules supported by Cisco 2600 series routers and the required release of
Cisco IOS software for each module.
If required, see Chapter 3, “Installing Network Modules in Cisco Modular Routers” for
instructions on installing a network module in your router.

Cisco 2600 Series Specifications

General

Connectivity Technology	Wired
Network/Transport Protocol	TCP/IP, IPX/SPX, AppleTalk
Operating System	Cisco IOS
Memory	16 MB DRAM
Flash Memory	8 MB
Interfaces	Ethernet, Serial, ISDN BRI
Expansion Slots	1 network module slots
Routing Protocols	RIP, EIGRP, OSPF, BGP
Product Type	Router
Form Factor	Rack-mountable
Data Link Protocol	Ethernet, Fast Ethernet, Serial, ISDN
Remote Management Protocol	SNMP, Telnet
Power Supply	Internal AC power supply

Summary

Chapter 1 Overview of Cisco Network Modules

Cisco 3600 Series Routers

Cisco 2600 Series Routers

Chapter 2 Preparing to Install Network Modules

Safety Information

Provides safety warnings and recommendations for installing network modules in Cisco modular routers.

Required Tools and Equipment

Lists the necessary tools and equipment for installing network modules in Cisco modular routers.

Chapter 3 Installing Network Modules in Cisco Modular Routers

Installing a Network Module in a Modular Router Chassis Slot

Provides step-by-step instructions for installing a network module into a router chassis slot.

Installing a WAN Interface Card in a Network Module Slot

Details the procedure for installing a WAN interface card into a network module slot.

Chapter 4 Connecting Ethernet Network Modules to a Network

1-Port and 4-Port Ethernet Modules

Provides information on 1-port and 4-port Ethernet modules, including connectors and LEDs.

1-Port Fast Ethernet Module

Describes the 1-port Fast Ethernet network module, its connection, and LEDs.

Chapter 5 Connecting Fast Ethernet PRI Network Modules to a Network

1-Port Fast Ethernet and 1-Port or 2-Port Channelized T1;ISDN PRI Network Modules

Chapter 6 Connecting Serial Network Modules to a Network

Connecting Asynchronous Network Modules to Asynchronous Devices

4-Port Serial Network Module

Information on the 4-port serial network module, its capabilities, and connection types.

16-Port and 32-Port Asynchronous Serial Network Module

Describes 16-port and 32-port asynchronous serial network modules and their interfaces.

Chapter 7 Connecting ISDN BRI Network Modules to a Network

Upgrading ISDN BRI Network Modules

4-Port and 8-Port ISDN BRI S;T Network Modules

Information on 4-port and 8-port ISDN BRI S/T modules, their connections, and LEDs.

4-Port and 8-Port ISDN BRI U Network Modules

Chapter 8 Connecting ISDN PRI Network Modules to a Network

1-Port and 2-Port Channelized T1;ISDN PRI Network Modules

1-Port and 2-Port Channelized E1;ISDN PRI Balanced (120-ohm) Network Modules

1-Port and 2-Port Channelized E1;ISDN PRI Unbalanced (75-ohm) Network Modules

Chapter 9 Connecting Voice Network Modules to a Network

2-Channel and 4-Channel Voice Network Modules

Chapter 10 Connecting Digital Modem Network Modules to a Network

Hardware Requirements

Specifies hardware requirements for digital modem modules, including PRI/BRI module revision levels.

Adding 6-Port MICA Modules to a Digital Modem Network Module

Chapter 11 Connecting Analog Modem Network Modules to a Network

8-Port and 16-Port Analog Modem Network Modules

Interface Numbering

Chapter 12 Connecting ATM Network Modules to a Network

ATM-25 Network Module

Chapter 13 Connecting HSSI Network Modules to a Network

HSSI Network Module

Chapter 14 Connecting Compression Network Modules to a Network

Compression Network Module