EasyManuals Logo

Cisco Firepower 1140 Getting Started

Cisco Firepower 1140
42 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #28 background imageLoading...
Page #28 background image
Can be changed during initial
configuration?DefaultSetting
Yes.IPv4: Obtained through DHCP from
Internet Service Provider (ISP) or upstream
router.
IPv6: Autoconfiguration.
Firepower 4100/9300: Data interfaces are
not pre-configured.
ISA 3000: BVI1 IP address is not
preconfigured. BVI1 includes all inside and
outside interfaces.
Outside interface IP address.
Default Interfaces by Device Model
You cannot select different inside and outside interfaces during initial configuration. To change the interface
assignments after configuration, edit the interface and DHCP settings. You must remove an interface from
the bridge group before you can configure it as a non-switched interface.
Inside InterfaceOutside InterfaceFTD device
VLAN1, which includes all other switch
ports except the outside interface, which is
a physical firewall interface.
Ethernet1/1Firepower 1010
Ethernet1/2Ethernet1/1Firepower 1120, 1140, 1150
Ethernet1/2Ethernet1/1Firepower 2100 series
Ethernet1/2Ethernet1/1Secure Firewall 3100 series
Data interfaces are not pre-configured.Data interfaces are not pre-configured.Firepower 4100 series
Data interfaces are not pre-configured.Data interfaces are not pre-configured.Firepower 9300 appliance
GigabitEthernet0/1GigabitEthernet0/0FTDv
GigabitEthernet1/2 and GigabitEthernet1/4GigabitEthernet1/1 and GigabitEthernet1/3
GigabitEthernet1/1 (outside1) and 1/2
(inside1), and GigabitEthernet1/3 (outside2)
and 1/4 (inside2) (non-fiber models only)
are configured as Hardware Bypass pairs.
All inside and outside interfaces are part of
BVI1.
ISA 3000
Getting Started
28
Getting Started
Default Configuration Prior to Initial Setup

Other manuals for Cisco Firepower 1140

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco Firepower 1140 and is the answer not in the manual?

Cisco Firepower 1140 Specifications

General IconGeneral
Processor cores16
Processor familyIntel
Built-in processorYes
Firewall throughput2200 Mbit/s
IPSec VPN throughput1.2 Gbit/s
Maximum firewall connections400000
Maximum firewall connections per second100000
Wi-FiNo
Supported network protocolsSMTP
Console portRJ-45
Connectivity technologyWired
SFP module slots quantity4
Ethernet LAN (RJ-45) ports8
USB 3.2 Gen 1 (3.1 Gen 1) Type-A ports quantity1
SSD capacity200 GB
Storage media typeSSD
Form factor1U
Input current2 A
AC input voltage100-240 V
AC input frequency50 - 60 Hz
Power consumption (max)100 W
Operating altitude0 - 3000 m
Storage temperature (T-T)-25 - 70 °C
Operating temperature (T-T)0 - 40 °C
Operating relative humidity (H-H)10 - 90 %
Country of originMexico
Quantity per pack1 pc(s)
Harmonized System (HS) code85176990
Package depth1409.7 mm
Package width990.6 mm
Package height457.2 mm
Package weight5782.31 g
Weight and Dimensions IconWeight and Dimensions
Depth436.9 mm
Width268.7 mm
Height43.7 mm

Related product manuals