1/3
Component identification
Minute hand
Date indication
Mode hand
Reception indication
• RX: reception-in-progress
• H/M/L/NO: Reception result
Hour hand
Function hand
• Power reserve
• Chronograph minute
• Day of week
Second hand
24-hour hand
ON/OFF indication
• Summer time
• Alarm hand
Button
B
Button
A
Crown
• Actual appearance may differ from the illustration.
• The crown has two positions when pulling it out.
• Refer also to our web page for detail of usage of the
scale and bezel on the watch.
(
http://www.citizenwatch-global.com/support/
pdf/enhanced/e.pdf
)
Changing the mode
This watch features the eight different modes as follows:
LON
The time of London and areas of the same time zone is indicated.
NYC
The time of New York and areas of the same time zone is indicated.
CHI
The time of Chicago and areas of the same time zone is indicated.
DEN
The time of Denver and areas of the same time zone is indicated.
LAX
The time of Los Angeles and areas of the same time zone is indicated.
CHR
Mode for using the chronograph.
ALM
Mode for using the alarm function.
A-TM
Mode for setting time difference from UTC (Coordinated Universal Time) and
indicating the time of a different time zone.
1.
Pull the crown out to position
1
.
The second hand points to 30 seconds and stops.
2.
Rotate the crown to change the mode.
• Turn the crown so that the mode hand will point to a marker of the mode
indication securely.
3.
Push the crown in to position
0
to finish the procedure.
Indication of the watch changes into that of the mode selected.
• It may take some time to change indication.
E650 Abbreviated instruction
• This watch is solar-powered. Expose the dial to light and use it sufficiently charged.
• To see details of charging time, specifications and operations, refer to the instruction manual:
E650 instruction manual
English
Checking the power reserve
1.
Change the mode to [LON], [NYC], [CHI], [DEN], [LAX] or [A-TM]
and push the crown in to position
0
.
2.
Press and release the lower right button
A
.
The second hand indicates reception result and the function hand indicates
power reserve in levels.
3.
Press and release the lower right button
A
to finish the
procedure.
• It returns to normal indication automatically in about 10 seconds without
pressing the button.
Indication of power reserve in levels
Level
3 2 1 0
Indication
Duration
(approx.)
10 - 7 months 7 - 1 month 1 month - 3 days 3 days ‒
Meaning
Power reserve is
sufficient.
Power reserve is
OK.
Power reserve is
getting low.
Insufficient
charge warning
has started.
OK for normal use. Charge immediately
Checking the signal reception result
• This watch receives the time signal at 2:00 AM every day and adjust the time
and calendar automatically. If the 2:00 AM reception was unsuccessful, it tries
signal reception again at 3:00 AM and 4:00 AM.
1.
Change the mode to [LON], [NYC], [CHI], [DEN] or [LAX] and push
the crown in to position
0
.
2.
Press and release the lower right button
A
.
The second hand indicates reception result and the function hand indicates
power reserve in levels.
Indication Reception result
H
Received signals in a very good condition
M
Received signals in a good condition
L
Received signals in a not-good condition
NO
The reception failed.
• “H”, “M” and “L” only indicate the condition for reception, not related to
the reception performance of the watch.
• Try signal reception following the steps in
Receiving the signal manually
(on-demand reception)
if the last reception failed.
3.
Press and release the lower right button
A
to finish the
procedure.
• It returns to normal indication automatically in about 10 seconds without
pressing the button.
Crown's position
0 1 2
To Next Page
Need help?
General
