Why has my Citizen Watch stopped working?
If your Citizen watch has stopped, the charge level indicator might be at level 0. To resolve this, charge the watch sufficiently until the charge level indicator reaches level 3, as indicated in 'Guide to Charging Time'.
What to do if the hands or digital displays on my Citizen JY8085-14H are abnormal?
If your Citizen watch hands or digital displays are acting abnormally, try resetting the watch.
Why is the second hand on my Citizen Watch moving in 2-second intervals?
If the second hand on your Citizen watch is moving in 2-second intervals, it could indicate a low charge. Charge the watch sufficiently until the charge level indicator reaches the fully charged level. Alternatively, 'ERR' might be displayed in digital display 1, in this case you should reset the watch and then correct the reference position.
Why is my Citizen Watch not receiving radio signals?
If your Citizen Watch isn't receiving radio signals, several factors could be at play. First, ensure that the home city setting (digital display 2) corresponds to your current reception area by checking the map and adjusting the setting accordingly. Additionally, obstructions or electronic noise could interfere with signal reception; try moving away from potential sources of interference and orient the watch with the 9:00 position facing the radio signal transmitter. Avoid moving the watch while it is receiving a signal. If the second hand is moving at 2-second intervals, charge the watch sufficiently by placing it in direct sunlight. Make sure that the mode is set to TME, CAL, or RX-S by pulling the crown out to position 1 and setting the mode accordingly. If the reception status is NO, c...
Describes the watch as a radio controlled, world time, Eco-Drive model.
Instructions on verifying watch hands alignment with the reference position.
Details on the watch's automatic radio wave reception process.
Procedure for manually receiving radio signals to set time and date.
Process for automatic reception after the watch stops due to insufficient charge.
Mapping of cities to specific radio wave transmitters for time synchronization.
List of cities, their UTC time differences, and assigned radio wave transmitters.
Explanation of the watch's four-grade charge level indicator.
Overview of the watch's eight operational modes.
Procedure for swapping home and world time displays for travel.
Definition and purpose of daylight saving time systems.
Methods for activating or deactivating daylight saving time settings.
Manual procedure for setting the watch's time using the digital display.
Manual procedure for setting the watch's date using the digital display.
Steps for configuring the timer function, including setting the time.
Instructions on operating the timer, including start, stop, and reset functions.
Guide to operating the chronograph for time measurement.
Configuring daylight saving time and city visibility for world time display.
Procedure to manually set time differences for user-defined cities.
Steps for setting the time, city, and activation status for alarms.
Selecting automatic update of daylight saving time via radio wave reception.
Configuring the watch's automatic radio wave reception schedule.
Details on default settings after a watch reset operation.
Step-by-step guide to reset the watch to its factory default state.
How to use the rotating bezel for calculations and measurements.
Using the bezel to estimate elapsed time intervals.
Using the bezel to estimate time remaining until a target time.
Instructions for using the bezel for navigation-related calculations.
Using the slide rule bezel for performing multiplication.
Using the slide rule bezel for performing division.
Using the slide rule bezel to determine ratios and solve proportional problems.
Using the slide rule bezel to calculate square roots.
Tips for optimal performance and charging of the solar-powered watch.
Describes the standard display when the watch has sufficient charge.
Indicates the watch's behavior when charge level is low.
How the watch behaves after recharging and receiving a signal.
Standard display mode before power saving is activated.
Description of the first level of power saving, turning off digital displays.
Description of the second level of power saving, stopping the hands.
How to exit power saving mode by exposure to light.
Safety warnings and procedures regarding the watch's secondary battery.
Warning against using incorrect or non-specified batteries.
Important safety advice for charging the watch to prevent damage.
Common problems and solutions related to radio signal reception.
Troubleshooting tips for issues related to the watch's solar power system.
Information on the watch's water resistance levels and usage limitations.
Advice on cleaning the watch to maintain its condition and functionality.
Detailed instructions for cleaning different parts of the watch.
Overview of the various information displayed on the watch's analog and digital screens.
Description of information shown in the watch's analog display sections.
Description of information shown in the watch's digital display sections.
List of extra features and functionalities available on the watch.
General| Brand | Citizen |
|---|---|
| Model | JY8085-14H |
| Movement | Eco-Drive |
| Water Resistance | 200 meters |
| Case Material | Stainless Steel |
| Dial Color | Black |
| Crystal | Sapphire |
| Features | Chronograph |
| Band Material | Stainless Steel |
| Functions | World Time |
| Case Diameter | 45 mm |
To Next Page