Clarion DRX6575RZ - RDS Traffic and Programme Information; Traffic Announcement (TA); Programme Type (PTY) Selection

RDS Operations
TA (Traffic Announcement)
In TA standby mode, when a traffic announcement
broadcast starts, the traffic announcement broad-
cast is received as top priority regardless of the
function mode so you can listen to it. Traffic
programme (TP) automatic tuning is also possible.
* This function can only be used when “TP” is lit in
the display. When “TP” is lit, this means that the
RDS broadcast station being received has traffic
announcement programmes.
© Setting TA standby mode
If you press TA button [11] when only “TP” is lit in the
display, “TP” and “TA” light in the display and the unit
is set into TA standby mode until a traffic announce-
ment is broadcast. When a traffic announcement
broadcast starts, “TRA INFO” appears in the display.
If you press TA button while a traffic announce-
ment broadcast is being received, the traffic announce-
ment broadcast reception is cancelled and the unit
goes into TA standby mode.
©@ Cancelling TA standby mode
With “TP” and “TA” lit in the display, press TA
button [11]. The “TA” in the display goes off and
TA standby mode is cancelled.
* If "TP” is not lit, pressing TA button searches
for a TP station.
©® Searching for a TP station
When “TP” is not lit, if you press TA button [fi],
“TA” in the display lights and the unit automati-
cally receives a TP station.
Note:
° 1fa TP station is not received, the unit continues the
search operation. Pressing TA button [fi] again goes
off “TA” in the display and stops TP station searching.
Auto store function for TP stations
You can automatically store up to 6 TP stations into
preset memory. If the number of TP that can be
received is less than 6, broadcast stations already
stored in memory are left without being overwritten.
With “TA” lit in the display, press and hold AS button [5]
for 2 seconds or longer. The TP stations with the good
reception sensitivity are stored into preset memory.
* Even if you select FM1 or FM2, a TP station is
stored into memory for FMS.
PTY
This function enables you to listen to a broadcast
of the selected programme type when it starts even
if the unit is on a function mode other than radio.
* Some countries do not yet have PTY broadcast.
* In TA standby mode, a TP station has priority over
a PTY broadcast station.
© Setting PTY standby mode
When you press PTY button [7], “PTY” lights in
the display and the PTY standby mode is turned
on. When the selected PTY broadcast starts, the
PTY item name appears in the display.
©® Cancelling PTY standby mode
When you press and hold PTY button for 1
second or longer, “PTY” goes off in the display
and PTY standby mode is cancelled.
@ Cancelling a PTY interrupt broadcast
Press PTY button during the PTY interrupt
broadcast, the PTY interrupt is cancelled and the
unit returns to PTY standby mode.
Selecting PTY
1. When you press PTY button [7], the unit goes
into PTY select mode.
2. Press any one of Preset buttons [9]. Alterna-
tively, turn the Rotary knob clockwise or
counterclockwise to select the desired PTY.
* Below are the factory default settings stored
for Preset buttons [9].
8. The PTY select mode is cancelled automati-
cally 7 seconds after a PTY is selected.
PTY seek
1. When you press PTY button [7|, the PTY se-
lect mode is turned on.
2. Select PTY.
3. Press the right or left side of SEARCH button
[14]. If you press the right side, the unit seeks
a PTY broadcast moving up the frequencies;
if you press the left side, it seeks moving down
the frequencies.
* [fno station with the selected PTY broadcast can
be received, the unit returns to PTY select mode.
PTY preset memory
1. When you press PTY button [7], the PTY se-
lect mode is turned on.
DRX6575Rz 15