Clarion ProAudio DXZ545MP - Adjusting the Tone

DXZ545MP 13
English
2. Press the [A-M] button and turning the
[ROTARY] knob clockwise adjusts in the +
direction; tuning it counterclockwise adjusts
in the – direction.
● When “B-BOOST 0” selected, you can ad-
just the bass in the range of –3 to 3.
● When “IMPACT 0” selected, you can adjust
the bass and treble in the range of –3 to 3.
● When “EXCITE 0” selected, you can adjust
the bass and treble in the range of –3 to 3.
∗ When Z-Enhancer Plus is selected, press and
hold the [Z+] button for 1 second or longer to
change to the “CUSTOM” mode.
Bass/treble characteristics become flat and
the indication “Z+ FLAT” is shown in the dis-
play.
Adjusting the tone
Press the [A-M] button and select the item to
adjust. Each time you press the [A-M] button,
the item changes as following order:
● When “BASS BOOST” is set
“SW-VOL 0” ➜ “B-BOOST 0” ➜ “BAL 0” ➜
“FADER 0” ➜ Last function mode.
● When “IMPACT” is set
“SW-VOL 0” ➜ “IMPACT 0” ➜ “BAL 0” ➜
“FADER 0” ➜ Last function mode.
● When “EXCITE” is set
“SW-VOL 0” ➜ “EXCITE 0” ➜ “BAL 0” ➜
“FADER 0” ➜ Last function mode.
● When “CUSTOM” is set
“SW-VOL 0” ➜ “BASS” ➜ “TREBLE” ➜
“BAL 0” ➜ “FADER 0” ➜ Last function
mode.
● When “Z+ OFF” is set
“SW-VOL 0” ➜ “BAL 0” ➜ “FADER 0” ➜
Last function mode.
∗ If subwoofer is effective, “SW-VOL 0” can be se-
lected.
Adjusting the subwoofer
When you default select one of mode (LPF50,
LPF80, LPF120)
1. Press the [A-M] button and select
“SW-VOL 0”.
2. Turning the [ROTARY] knob clockwise or
counterclockwise to adjust the subwoofer
volume.
∗ The factory default setting is “SW-VOL 0”.
(Adjustment range: -6 to +6)
3. When the adjustment is complete, press the
[A-M] button several times until the function
mode is reached.
Adjusting the bass (Gain,
Frequency, Q-curve)
This adjustment can be performed when the Z-
Enhancer Plus is set to “CUSTOM”.
1. Press the [A-M] button and select “BASS”.
2. Turning the [ROTARY] knob clockwise em-
phasizes the bass; turning it counterclock-
wise attenuates the bass.
∗ The factory default setting is “B
ÅÅ
ÅÅ
Å
GAIN 0
ÎÎ
ÎÎ
Î
”.
(Adjustment range: –6 to +8)
3. Press the [a] or [d] button to select
“B
ÅÅ
ÅÅ
Å
FREQ 50
ÎÎ
ÎÎ
Î
”.
Turning the [ROTARY] knob clockwise or
counterclockwise to select the frequency.
∗ The factory default setting is “B
ÅÅ
ÅÅ
Å
FREQ 50
ÎÎ
ÎÎ
Î
”.
(Adjustment 50/80/120 Hz)
4. Press the [a] or [d] button to select “B
ÅÅ
ÅÅ
Å
Q 1
ÎÎ
ÎÎ
Î
”.
Turning the [ROTARY] knob clockwise or
counterclockwise to select the Q-curve.
∗ The factory default setting is “B
ÅÅ
ÅÅ
Å
Q 1
ÎÎ
ÎÎ
Î
”.
(Adjustment 1/1.25/1.5/2)
5. When the adjustment is complete, press the
[A-M] button several times until the function
mode is reached.
Adjusting the treble (Gain,
Frequency)
This adjustment can be performed when the Z-
Enhancer Plus is set to “CUSTOM”.
1. Press the [A-M] button and select “TREBLE”.
2. Turning the [ROTARY] knob clockwise em-
phasizes the treble; turning it counterclock-
wise attenuates the treble.
∗ The factory default setting is “T
ÅÅ
ÅÅ
Å
GAIN 0
ÎÎ
ÎÎ
Î
”.
(Adjustment range: –6 to +6)
3. Press the [a] or [d] button to select
“T
ÅÅ
ÅÅ
Å
FREQ 12k
ÎÎ
ÎÎ
Î
”.
Turning the [ROTARY] knob clockwise or
counterclockwise to select the frequency.
∗ The factory default setting is “T
ÅÅ
ÅÅ
Å
FREQ 12k
ÎÎ
ÎÎ
Î
”.
(Adjustment 8 kHz/12 kHz)
4. When the adjustment is complete, press the
[A-M] button several times until the function
mode is reached.
Basic Operations